XC2VP30-6FFG896I Xilinx Inc, XC2VP30-6FFG896I Datasheet - Page 67
![no-image](/images/no-image-200.jpg)
XC2VP30-6FFG896I
Manufacturer Part Number
XC2VP30-6FFG896I
Description
IC FPGA VIRTEX-II PRO 896-FBGA
Manufacturer
Xilinx Inc
Series
Virtex™-II Pror
Datasheet
1.XC2VP20-5FGG676C.pdf
(430 pages)
Specifications of XC2VP30-6FFG896I
Number Of Logic Elements/cells
30816
Number Of Labs/clbs
3424
Total Ram Bits
2506752
Number Of I /o
556
Voltage - Supply
1.425 V ~ 1.575 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
896-BBGA, FCBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Gates
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC2VP30-6FFG896I
Manufacturer:
XILINX
Quantity:
455
- Current page: 67 of 430
- Download datasheet (4Mb)
Configuration
Virtex-II Pro devices are configured by loading application
specific configuration data into the internal configuration
memory. Configuration is carried out using a subset of the
device pins, some of which are dedicated, while others can
be re-used as general purpose inputs and outputs once
configuration is complete.
Depending on the system design, several configuration
modes are supported, selectable via mode pins. The mode
pins M2, M1, and M0 are dedicated pins. The M2, M1, and
M0 mode pins should be set at a constant DC voltage level,
either through pull-up or pull-down resistors, or tied directly
to ground or V
during and after configuration.
An additional pin, HSWAP_EN is used in conjunction with
the mode pins to select whether user I/O pins have pull-ups
during configuration. By default, HSWAP_EN is tied High
(internal pull-up) which shuts off the pull-ups on the user I/O
pins during configuration. When HSWAP_EN is tied Low,
user I/Os have pull-ups during configuration. Other dedi-
cated pins are CCLK (the configuration clock pin), DONE,
PROG_B, and the Boundary-Scan pins: TDI, TDO, TMS,
and TCK. (The TDO pin is open-drain and does not have an
internal pull-up resistor.) Depending on the configuration
mode chosen, CCLK can be an output generated by the
FPGA, or an input accepting an externally generated clock.
The configuration pins and Boundary-Scan pins are inde-
pendent of the V
of 2.5V is used for these pins. All configuration pins are
LVCMOS25 12mA. See
Platform FPGAs: DC and Switching
A "persist" option is available which can be used to force the
configuration pins to retain their configuration function even
after device configuration is complete. If the persist option is
not selected then the configuration pins with the exception
of CCLK, PROG_B, and DONE can be used as user I/O in
normal operation. The persist option does not apply to the
Boundary-Scan related pins. The persist feature is valuable
in applications which employ partial reconfiguration or
reconfiguration on the fly.
Configuration Modes
Virtex-II Pro supports the following five configuration
modes:
•
•
•
•
•
Refer to
A detailed description of configuration modes is provided in
the Virtex-II Pro Platform FPGA User Guide.
DS083 (v4.7) November 5, 2007
Product Specification
Slave-Serial Mode
Master-Serial Mode
Slave SelectMAP Mode
Master SelectMAP Mode
Boundary-Scan (JTAG, IEEE 1532) Mode
Table 32, page
R
CCAUX
CCO
. The mode pins should not be toggled
. The auxiliary power supply (V
57.
Virtex-II Pro and Virtex-II Pro X
Characteristics.
Virtex-II Pro and Virtex-II Pro X Platform FPGAs: Functional Description
CCAUX
www.xilinx.com
)
Slave-Serial Mode
In slave-serial mode, the FPGA receives configuration data
in bit-serial form from a serial PROM or other serial source
of configuration data. The CCLK pin on the FPGA is an
input in this mode. The serial bitstream must be setup at the
DIN input pin a short time before each rising edge of the
externally generated CCLK.
Multiple FPGAs can be daisy-chained for configuration from
a single source. After a particular FPGA has been config-
ured, the data for the next device is routed internally to the
DOUT pin. The data on the DOUT pin changes on the falling
edge of CCLK.
Slave-serial mode is selected by applying [111] to the mode
pins (M2, M1, M0). A weak pull-up on the mode pins makes
slave serial the default mode if the pins are left uncon-
nected.
Master-Serial Mode
In master-serial mode, the CCLK pin is an output pin. It is the
Virtex-II Pro FPGA device that drives the configuration clock
on the CCLK pin to a Xilinx Serial PROM which in turn feeds
bit-serial data to the DIN input. The FPGA accepts this data
on each rising CCLK edge. After the FPGA has been loaded,
the data for the next device in a daisy-chain is presented on
the DOUT pin after the falling CCLK edge.
The interface is identical to slave serial except that an inter-
nal oscillator is used to generate the configuration clock
(CCLK). A wide range of frequencies can be selected for
CCLK which always starts at a slow default frequency. Con-
figuration bits then switch CCLK to a higher frequency for
the remainder of the configuration.
Slave SelectMAP Mode
The SelectMAP mode is the fastest configuration option.
Byte-wide data is written into the Virtex-II Pro FPGA device
with a BUSY flag controlling the flow of data. An external
data source provides a byte stream, CCLK, an active Low
Chip Select (CS_B) signal and a Write signal (RDWR_B). If
BUSY is asserted (High) by the FPGA, the data must be held
until BUSY goes Low. Data can also be read using the
SelectMAP mode. If RDWR_B is asserted, configuration
data is read out of the FPGA as part of a readback operation.
After configuration, the pins of the SelectMAP port can be
used as additional user I/O. Alternatively, the port can be
retained to permit high-speed 8-bit readback using the per-
sist option.
Multiple Virtex-II Pro FPGAs can be configured using the
SelectMAP mode, and be made to start-up simultaneously.
To configure multiple devices in this way, wire the individual
CCLK, Data, RDWR_B, and BUSY pins of all the devices in
parallel. The individual devices are loaded separately by
deasserting the CS_B pin of each device in turn and writing
the appropriate data.
Module 2 of 4
56
Related parts for XC2VP30-6FFG896I
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![XC2VP30-5FGG676C](/photos/6/73/67300/b-676_tmb.jpg)
Part Number:
Description:
IC VIRTEXIIPRO FPGA 30K 676FCBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FFG896C](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 896-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FFG1152C](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 1152-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FGG676I](/photos/6/73/67300/b-676_tmb.jpg)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 676-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-6FGG676C](/photos/6/73/67300/b-676_tmb.jpg)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 676-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-6FFG896C](/images/no-image3.png)
Part Number:
Description:
IC VIRTEXIIPRO FPGA 30K 896FCBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FFG896I](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 896-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FFG1152I](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 1152-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-6FGG676I](/photos/6/73/67300/b-676_tmb.jpg)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 676-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-7FGG676C](/photos/6/73/67300/b-676_tmb.jpg)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 676-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-7FFG896C](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 896-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-6FFG1152I](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 1152-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-7FFG1152C](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 1152-FBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FG676I](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 676FGBGA
Manufacturer:
Xilinx Inc
Datasheet:
![XC2VP30-5FF896I](/images/no-image3.png)
Part Number:
Description:
IC FPGA VIRTEX-II PRO 896FFBGA
Manufacturer:
Xilinx Inc
Datasheet: