XC4010E-1PQ160C Xilinx Inc, XC4010E-1PQ160C Datasheet - Page 18
![no-image](/images/no-image-200.jpg)
XC4010E-1PQ160C
Manufacturer Part Number
XC4010E-1PQ160C
Description
IC FPGA C-TEMP 5V 1SPD 160-PQFP
Manufacturer
Xilinx Inc
Series
XC4000E/Xr
Datasheet
1.XC4005E-4PC84C.pdf
(68 pages)
Specifications of XC4010E-1PQ160C
Number Of Logic Elements/cells
950
Number Of Labs/clbs
400
Total Ram Bits
12800
Number Of I /o
129
Number Of Gates
10000
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
160-BQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
XC4000E and XC4000X Series Field Programmable Gate Arrays
Table 8: Supported Sources for XC4000 Series Device
Inputs
XC4000XL 5-Volt Tolerant I/Os
The I/Os on the XC4000XL are fully 5-volt tolerant even
though the V
directly connect to the XC4000XL inputs without damage,
as shown in
applied before or after 5 volt signals are applied to the I/Os.
This makes the XC4000XL immune to power supply
sequencing problems.
Registered Inputs
The I1 and I2 signals that exit the block can each carry
either the direct or registered input signal.
The input and output storage elements in each IOB have a
common clock enable input, which, through configuration,
can be activated individually for the input or output flip-flop,
or both. This clock enable operates exactly like the EC pin
on the XC4000 Series CLB. It cannot be inverted within the
IOB.
The storage element behavior is shown in
Table 9: Input Register Functionality
(active rising edge is shown)
6-22
Any device, Vcc = 3.3 V,
CMOS outputs
XC4000 Series, Vcc = 5 V,
TTL outputs
Any device, Vcc = 5 V,
TTL outputs (Voh
Any device, Vcc = 5 V,
CMOS outputs
Power-Up or
GSR
Flip-Flop
Latch
Both
Legend:
Mode
__/
SR
0*
1*
X
Source
Table
CC
Don’t care
Rising edge
Set or Reset value. Reset is default.
Input is Low or unconnected (default value)
Input is High or unconnected (default value)
is 3.3 volts. This allows 5 V signals to
Clock
8. In addition, the 3.3 volt V
__/
3.7 V)
X
X
0
1
0
Product Obsolete or Under Obsolescence
Series Inputs
XC4000E/EX
TTL
5 V,
Enable
Clock
1*
1*
1*
X
X
0
CMOS
Unreli
-able
Data
5 V,
Table
Series Inputs
D
D
D
X
X
X
X
XC4000XL
CMOS
3.3 V
CC
9.
can be
SR
Q
D
Q
Q
D
Q
Optional Delay Guarantees Zero Hold Time
The data input to the register can optionally be delayed by
several nanoseconds. With the delay enabled, the setup
time of the input flip-flop is increased so that normal clock
routing does not result in a positive hold-time requirement.
A positive hold time requirement can lead to unreliable,
temperature- or processing-dependent operation.
The input flip-flop setup time is defined between the data
measured at the device I/O pin and the clock input at the
IOB (not at the clock pin). Any routing delay from the device
clock pin to the clock input of the IOB must, therefore, be
subtracted from this setup time to arrive at the real setup
time requirement relative to the device pins. A short speci-
fied setup time might, therefore, result in a negative setup
time at the device pins, i.e., a positive hold-time require-
ment.
When a delay is inserted on the data line, more clock delay
can be tolerated without causing a positive hold-time
requirement. Sufficient delay eliminates the possibility of a
data hold-time requirement at the external pin. The maxi-
mum delay is therefore inserted as the default.
The XC4000E IOB has a one-tap delay element: either the
delay is inserted (default), or it is not. The delay guarantees
a zero hold time with respect to clocks routed through any
of the XC4000E global clock buffers. (See
Buffers (XC4000E only)” on page 35
global clock buffers in the XC4000E.) For a shorter input
register setup time, with non-zero hold, attach a NODELAY
attribute or property to the flip-flop.
The XC4000X IOB has a two-tap delay element, with
choices of a full delay, a partial delay, or no delay. The
attributes or properties used to select the desired delay are
shown in
MEDDELAY, and NODELAY. The default setting, with no
added attribute, ensures no hold time with respect to any of
the XC4000X clock buffers, including the Global Low-Skew
buffers. MEDDELAY ensures no hold time with respect to
the Global Early buffers. Inputs with NODELAY may have a
positive hold time with respect to all clock buffers. For a
description of each of these buffers, see
Buffers (XC4000X only)” on page
Table 10: XC4000X IOB Input Delay Element
full delay
(default, no
attribute added)
MEDDELAY
NODELAY
Value
Table
10. The choices are no added attribute,
Zero Hold with respect to Global
Low-Skew Buffer, Global Early Buffer
Zero Hold with respect to Global Early
Buffer
Short Setup, positive Hold time
May 14, 1999 (Version 1.6)
When to Use
37.
for a description of the
“Global Nets and
“Global Nets and
R