101-0602 Rabbit Semiconductor, 101-0602 Datasheet - Page 32
101-0602
Manufacturer Part Number
101-0602
Description
COMPUTER SNGL BRD BL2500 44.2MHZ
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0576.pdf
(106 pages)
Specifications of 101-0602
Module/board Type
Single Board Computer Module
For Use With/related Products
BL2500
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 32 of 106
- Download datasheet (2Mb)
Based on the standard capacitor discharge formula, this means that the maximum voltage
change will be
This is a ripple of approximately 6 mV peak-to-peak.
Table 4 lists typical uncalibrated DA0 or DA1 voltages measured for various duty cycle
values with a load larger than 1 M.
The full D/A converter voltage range of 0–3.3 V cannot be realized because of the voltage
tolerances associated with the voltage regulator, the Rabbit 3000 PWM output, and the op-
amp rail. The circuit can achieve an actual voltage range of 0.1–3.3 V.
It is important to remember that the DA0 or DA1 output voltage will not be realized instan-
taneously after programming in a value. There is a settling time because of the RC time
constant (24.9 k × 100 nF), which is 2.5 ms. For example, the voltage at any given time is
where V is the voltage at time t, V
DA1 output voltage from the D/A converter, and RC is the time constant (2.5 ms). The
settling will be within 99.326% (or within about 22 mV for a 3.3 V change in voltage)
after five time constants, or 12.5 ms. Six time constants, 15 ms, will allow settling to
within 99.75% (or to within about 8 mV for a 3.3 V change in voltage). Seven time con-
stants, 17.5 ms, will allow settling to within 99.91% (or to within about 3 mV for a 3.3 V
change in voltage).
An LM324 op amp, which can comfortably source 10 mA throughout the D/A converter
range, drives the D/A converter output. If the output voltage is above 1 V, the D/A con-
verter can comfortably sink 10 mA. Below 1 V, the D/A converter can only sink a maxi-
mum of 100 µA.
To summarize, DA0 and DA1 are factory-calibrated, with the calibration constants stored
in flash memory. DA0 and DA1 can be programmed with a resolution of 3 mV and a
peak-to-peak ripple of 6 mV over the range from 0.1 to 3.1 V. The settling time to within 3
mV is 17.5 ms.
26
Table 4. Typical Uncalibrated DA0 or DA1 Voltages for Various Duty Cycles
V = V
1.65 V
P
– (V
Duty Cycle
P
1 e
100
– V
–
(%)
50
0
DA
–
----------------- -
2.5 ms
)e
8.7 µs
(-t/RC)
P
is the programmed voltage, V
=
Voltage
5.73 mV
0.086
1.628
3.244
(V)
Programmed Count
1023
512
1
DA
is the last DA0 or
Coyote (BL2500)
Related parts for 101-0602
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SNGLBD BL2101 A/D 0-10V
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
CARD D/A 0-10V SR9400 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
CARD A/D 0-10V SR9300 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools WIRELESS CONTROL APP KIT
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BD BL2010 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BD BL2020 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2000 MEM/FLSH
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD FLASH&HEADERS
Manufacturer:
Rabbit Semiconductor