ES1-LW100H Omron, ES1-LW100H Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
ES1-LW100H
Manufacturer Part Number
ES1-LW100H
Description
Sensor Hardware & Accessories Infrared Sensor
Manufacturer
Omron
Datasheet
1.ES1-LW100H.pdf
(64 pages)
Specifications of ES1-LW100H
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
26
E5@Z
Operation
Setting Levels Diagram
This diagram shows all of the setting levels. To move to the advanced function setting level, you must enter passwords. Some parameters are not
displayed depending on the protect level setting and the conditions of use.
Control stops when you move from the operation level to the initial setting level.
Note: 1. Moves to operation level by software reset.
Error Displays (Troubleshooting)
When an error occurs, the No.1 display shows the error code. Take necessary measure according to the error code, referring the table below.
Note: 1. If the input value exceeds the display limit ( 1999 to 9999), though it is within the control range,
s.err (S. Err)
e111 (E111)
h.err (H. Err)
Manual
mode
No. 1 display
2. From the manual control level, key operations can be used to move to the operation level only.
2. These errors are displayed only when the PV/SP is displayed. Errors are not displayed in other display modes.
For details on the control range, refer to the E5CZ/E5CZ-U/E5AZ/E5EZ Digital Temperature Controllers User's Manual (Cat. No. H207).
Manual Control
Level
Started in manual mode.
Press the O Key
for at least 1 s.
above 9999. Under these conditions, control output and alarm output will operate normally.
(See
note
2.)
Input error
(See note 2.)
A/D converter
error
(See note 2.)
Memory error
HB error
(See note 2.)
C
Meaning
a-m
Press the O Key for
at least 1 s; display
will flash.
Press the Ol Key for
at least 3 s while a-m
Press the O Key
for at least 1 s.
Check the wiring of inputs for miswiring, disconnections, and short-circuits and check the
input type.
Check for an input error and then cycle the power supply. If the same error is still
displayed, repairs will be necessary.
If the Temperature Controller is normal after cycling the power supply, the error may have
been caused by noise. Check for noise being generated nearby.
Cycle the power supply. If the same error is still displayed, repairs will be necessary.
If the Temperature Controller is normal after cycling the power supply, the error may have
been caused by noise. Check for noise being generated nearby.
Operation Level
Press the
O Key
for at
least 1 s.
Initial Setting Level
Power ON
Started in automatic mode.
Advanced Function
Setting Level
(See
note 1.)
Press the
O Key less than 1 s.
C
Input password.
Set value 169
Press the
O Key for less than 1 s.
Action
Adjustment Level
25
100
Press the O Key for at
least 1 s; display will flash.
Press the O Key for at
least 3 s.
Communi-
cations
Setting
Control stops.
Press the O
+ M Keys for
at least 1 s.
Control in progress
Control stopped
Not displayed for some models
Level change
Note: The time taken to move
Protect level
will be displayed under 1999 and
to the protect level can
be adjusted by
changing the "Move to
protect level time"
C
OFF
OFF
OFF
OFF
Press the O +
M keys; display
will flash.
25
Control
outputs
100
Press the O +
M Keys for at
least 3 s. (See
note.)
Output status at error
Operates as
above the upper
limit.
OFF
OFF
OFF
Alarm outputs