CS42416-DQZ Cirrus Logic Inc, CS42416-DQZ Datasheet - Page 22
![IC CODEC 6CH 110DB 192KHZ 64LQFP](/photos/6/80/68092/cs42888-dqz_sml.jpg)
CS42416-DQZ
Manufacturer Part Number
CS42416-DQZ
Description
IC CODEC 6CH 110DB 192KHZ 64LQFP
Manufacturer
Cirrus Logic Inc
Type
Audio Codecr
Datasheet
1.CS42416-CQZ.pdf
(73 pages)
Specifications of CS42416-DQZ
Data Interface
Serial
Resolution (bits)
24 b
Number Of Adcs / Dacs
2 / 6
Sigma Delta
Yes
Dynamic Range, Adcs / Dacs (db) Typ
114 / 110
Voltage - Supply, Analog
4.75 V ~ 5.25 V
Voltage - Supply, Digital
3.13 V ~ 5.25 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Audio Codec Type
Stereo
No. Of Adcs
2
No. Of Dacs
6
No. Of Input Channels
2
No. Of Output Channels
13
Adc / Dac Resolution
24bit
Sampling Rate
192kSPS
Ic Interface Type
I2C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS42416-DQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Company:
Part Number:
CS42416-DQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
22
4.3.3
4.3.4
DAC_SDINx
Digital Volume and Mute Control
Each DAC’s output level is controlled via the Volume Control registers operating over the range of 0 to
-127 dB attenuation with 0.5 dB resolution. See
14h)” on page
rate controlled by the SZC[1:0] bits in the Digital Volume Control register. See
(address 0Dh)” on page
Each output can be independently muted via mute control bits in the register
0Eh)” on page
value (-127 dB). When the XX_MUTE bit is disabled, the corresponding DAC returns to the attenuation
level set in the Volume Control register. The attenuation is ramped up and down at the rate specified by
the SZC[1:0] bits.
The Mute Control pin, MUTEC, is typically connected to an external mute control circuit. The Mute Control
pin outputs high impedance during Power-Up or in Power-Down Mode by setting the PDN bit in the reg-
ister
controlled by the user via the control port, or automatically asserted high when zero data is present on all
DAC inputs, or when serial port clock errors are present. To prevent large transients on the output, it is
desirable to mute the DAC outputs before the Mute Control pin is asserted. Please see the MUTEC pin
in the Pin Descriptions section for more information.
Each of the GPO1-GPO7 can be programmed to provide a hardware MUTE signal to individual circuits.
Each pin can be programmed as an output, with specific muting capabilities as defined by the function
bits in the register
ATAPI Specification
The CS42416 implements the channel-mixing functions of the ATAPI CD-ROM specification. The
ATAPI functions are applied per A-B pair. Refer to
mation.
“Power Control (address 02h)” on page 43
Right Channel
Left Channel
Audio Data
Audio Data
52. When enabled, each XX_MUTE bit attenuates the corresponding DAC to its maximum
53. Volume control changes are programmable to ramp in increments of 0.125 dB at the
“General-Purpose Pin Control (addresses 29h to 2Fh)” on page
Figure 9. ATAPI Block Diagram (x = channel pair 1, 2, 3)
51.
Σ
to a ‘1’. Once out of Power-Down Mode, the pin can be
“Volume Control (addresses 0Fh, 10h, 11h, 12h, 13h,
Table 14 on page 54
A Channel
B Channel
Volum e
Volum e
Control
Control
and
Σ
Figure 9
“Volume Transition Control
“Channel Mute (address
58.
for additional infor-
MUTE
MUTE
CS42416
AOUTAx
AOUTBx
DS602F1