USBN9604-28M/NOPB National Semiconductor, USBN9604-28M/NOPB Datasheet - Page 8
![IC CONTROLLER SERIAL BUS 28-SOIC](/photos/6/59/65917/pkg_m28b_sml.jpg)
USBN9604-28M/NOPB
Manufacturer Part Number
USBN9604-28M/NOPB
Description
IC CONTROLLER SERIAL BUS 28-SOIC
Manufacturer
National Semiconductor
Datasheet
1.USBN9604-28MNOPB.pdf
(60 pages)
Specifications of USBN9604-28M/NOPB
Controller Type
USB 2.0 Controller
Interface
Parallel/Serial
Voltage - Supply
3 V ~ 5.5 V
Current - Supply
30mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
28-SOIC (7.5mm Width)
For Use With
USBN9604-HS-EB - KIT NODE CONTROLLER SAMPLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*USBN9604-28M
*USBN9604-28M/NOPB
USBN9604-28M
*USBN9604-28M/NOPB
USBN9604-28M
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
USBN9604-28M/NOPB
Manufacturer:
Freescale
Quantity:
2 314
Part Number:
USBN9604-28M/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
www.national.com
1.0 Signal/Pin Connection and Description
External Elements
Choose C1 and C2 capacitors (see Figure 1) to match the crystal’s load capacitance. The load capacitance C
the crystal is comprised of C1 in series with C2, and in parallel with the parasitic capacitance of the circuit. The parasitic
capacitance is caused by the chip package, board layout and socket (if any), and can vary from 0 to 8 pF. The rule of thumb
in choosing these capacitors is:
C
1.2.3
1.2.4
L
= (C1*C2)/(C1+C2)+C Parasitic
I/O
I/O
I/O
I/O
O
O
I
I
I
I
USB Port
Microprocessor Interface
MODE1-0 Interface Mode. Each of these pins should be hard-wired to V
Name
DACK
Name
D+
D–
INTR
DRQ
CS
RD
Resistor R2
Capacitor C1
Capacitor C2
Component
USB D+ Upstream Port. This pin requires an external 1.5k pull-up to 3.3V to signal full speed
operation.
USB D– Upstream Port
C1
face mode:
MODE1-0 = 00. Mode 0: Non-multiplexed parallel interface mode
MODE1-0 = 01. Mode 1: Multiplexed parallel interface mode
MODE1-0 = 10. Mode 2: MICROWIRE interface mode
MODE1-0 = 11. Mode 3: Reserved
Note: Mode 3 also selects the MICROWIRE interface mode in the USBN9602, but this mode
should be reserved to preserve compatibility with future devices.
DMA Acknowledge. This active low signal is only used if DMA is enabled. If DMA is not used,
this pin must be tied to V
DMA Request. This pin is used for DMA request only if DMA is enabled.
Interrupt. The interrupt signal modes (active high, active low or open drain) can be config-
ured via the Main Control register. During reset, this signal is TRI-STATE .
Chip Select. Active low chip select
Read. Active low read strobe, parallel interface
C2
Figure 1. Typical Oscillator Circuit
XTAL
CC
Parameters
.
R2
8
(Continued)
Description
Description
R1
Values
15 pF
15 pF
XIN
XOUT
0
CC
or GND to select the inter-
Tolerance
20%
20%
L
“seen” by