MCP2515-E/SO Microchip Technology, MCP2515-E/SO Datasheet - Page 3
![IC CAN CONTROLLER W/SPI 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
MCP2515-E/SO
Manufacturer Part Number
MCP2515-E/SO
Description
IC CAN CONTROLLER W/SPI 18SOIC
Manufacturer
Microchip Technology
Specifications of MCP2515-E/SO
Package / Case
18-SOIC (7.5mm Width)
Controller Type
CAN Interface
Interface
SPI
Voltage - Supply
2.7 V ~ 5.5 V
Current - Supply
10mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Product
Controller Area Network (CAN)
Number Of Transceivers
1
Data Rate
1 Mbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Supply Current (max)
10 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP2515DM-BM - BOARD DEMO FOR MCP2515/51MCP2515DM-PTPLS - BOARD DAUGHTER PICTAIL MCP2515MCP2515DM-PCTL - BOARD DEMO FOR MCP2515DV251001 - KIT DEVELOPMENT CAN MCP2510
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP2515-E/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
1.0
The MCP2515 is a stand-alone CAN controller
developed to simplify applications that require
interfacing with a CAN bus. A simple block diagram of
the MCP2515 is shown in
consists of three main blocks:
1.
2.
3.
An example system implementation using the device is
shown in
1.1
The CAN module handles all functions for receiving
and transmitting messages on the CAN bus. Messages
are transmitted by first loading the appropriate
message buffer and control registers. Transmission is
initiated by using control register bits via the SPI
interface or by using the transmit enable pins. Status
and errors can be checked by reading the appropriate
registers. Any message detected on the CAN bus is
checked for errors and then matched against the user-
defined filters to see if it should be moved into one of
the two receive buffers.
FIGURE 1-1:
© 2010 Microchip Technology Inc.
CLKOUT
The CAN module, which includes the CAN
protocol engine, masks, filters, transmit and
receive buffers.
The control logic and registers that are used to
configure the device and its operation.
The SPI protocol block.
OSC1
OSC2
RXCAN
TXCAN
DEVICE OVERVIEW
CAN Module
Figure
CAN Module
1-2.
Generation
Protocol
Engine
CAN
Timing
BLOCK DIAGRAM
Figure
1-1. The device
Registers
Interrupt
Control
and
TX and RX Buffers
Masks and Filters
Control Logic
1.2
The control logic block controls the setup and operation
of the MCP2515 by interfacing to the other blocks in
order to pass information and control.
Interrupt pins are provided to allow greater system
flexibility. There is one multi-purpose interrupt pin (as
well as specific interrupt pins) for each of the receive
registers that can be used to indicate a valid message
has been received and loaded into one of the receive
buffers. Use of the specific interrupt pins is optional.
The general purpose interrupt pin, as well as status
registers (accessed via the SPI interface), can also be
used to determine when a valid message has been
received.
Additionally, there are three pins available to initiate
immediate transmission of a message that has been
loaded into one of the three transmit registers. Use of
these
transmissions can also be accomplished by utilizing
control registers, accessed via the SPI interface.
1.3
The MCU interfaces to the device via the SPI interface.
Writing to, and reading from, all registers is
accomplished using standard SPI read and write
commands, in addition to specialized SPI commands.
pins
Control Logic
SPI Protocol Block
is
optional,
Interface
Logic
SPI
as
MCP2515
initiating
DS21801F-page 3
CS
SCK
SI
SO
INT
RX0BF
RX1BF
TX0RTS
TX1RTS
TX2RTS
RESET
message
SPI
Bus