FEATURES
DESCRIPTION
The PF600 AC-DC converter module provides a highly-
integrated, high-density solution for the front-end of a
48Vdc distributed power architecture (DPA). This unit
delivers the full-rated 600W of output power over the
input range of 90-264Vac while providing harmonic
correction to EN61000-3-2.
Unlike competitive offerings, the PF600 provides a full-
isolated output, permitting implementations with either
isolated or non-isolated DC-DC converters.
The wide input voltage range of 85-264Vac facili-
tates use in products designed for global deployment.
The isolated output also permits the user to polarize the
output as the specific application may require.
The high-efficiency architecture and baseplate-cooled
design simplify thermal management.
profile package makes this an ideal choice for 1U and
2U chassis applications where density and efficiency
are strategic design considerations.
Proprietary design techniques combined with automat-
ed manufacturing in fully ISO-9001 certified facilities
results in a compact, reliable, and efficient product that
provides a cost-effective solution.
With global safety agency approvals, the PF600 is a
comprehensive solution to a complex problem bounded
by the competing pressures of development cycle time,
efficiency, cost, and packagin
www.murata-ps.com
Compact 2.55"x5"x0.56" package
600W power at -10ºC to +100ºC
Power density >84W per in3
Up to 89% efficiency
90-264Vac global input range
12V at 50mA standby output
DC OK signal
Temperature monitoring output
Harmonic correction to EN61000-3-2
cUL & VDE approved to 60950-1
Output remote ON/OFF control
The low-
Notes:
SELECTION GUIDE
PF600-1
INPUT CHARACTERISTICS
Parameter
Input Operating Voltage
Input Frequency
Input Current
Power Factor
Inrush Current
Quiescent Input Power
OUTPUT CHARACTERISTICS
Parameter
Output Power
Main Output Voltage (Vo)
Main Output Current (Io)
Standby Output Voltage (Vsb)
Standby Output Current (Isb)
PARD (Vo)
PARD (Vsb)
Turn-On Delay (Vo)
Output Holdup Time
Isolation, Pri-Sec
Isolation, Pri-Chassis
Isolation, Sec-Chassis
GENERAL CHARACTERISTICS
Parameter
Efficiency
Switching Frequency
MTBF
Weight
Model Number
1 Full 600W power available at input voltages above 90Vac; de-rate output to 550W at 85Vac.
2 An external bulk capacitor is connected to terminals C+ and C- (pins 4 & 5) is required for operation. The minimum
Contact factory for replacement model
required capacitance is 100uF; the maximum value is 1000uF. The ripple current rating for this capacitor should
exceed 3Arms at 300kHz. The minimum voltage rating for the bulk capacitor is 450Vdc. Additional information on
holdup time is available in application note ACAN-10.
urre
y
RACTE
Vo
oltage
urr
C
OBSOLETE PRODUCT
(Io)
(Io)
ERISTICS
)
Power
600W
sb)
sb)
)
Conditions
All line, load
All line, load
All line, load
Io>25%
240Vac, avg. over 1 cycle
SB output unloaded, output inhibited, 230Vac
Output enabled but unloaded
onditions
>25%
Conditions
Conditions
600W load, 90Vac
600W lo
600W load, 264Vac
MIL-HDBK-217F, 100ºC
Unpackaged
s
Conditions
90-264Vac
All line, load, temp, & 90% load step
All line, load, tem
All line, load, tem
5%-100% static load, 0-100ºC
5%-1
5%-1
100kHz-20MHz
Low freq ripple
20MHz bandwidth
Full load, 470uF bulk cap
1
1
1
0-264Va
& environmental
& e
&
environmental
Main Output
48V@12.5A
00% static load, 0
00% static load, 0
vironmen
c
c
mp, & 90% load ste
p, & 90% load st
600W AC/DC Front-End Power Module
cap
0-100ºC
2
2
Standby Output
12V@50mA
12V@50mA
12V@50mA
ep
Output
PF600 SERIES
0.95
Min
85
47
44.5
Min
500
1.5
1
36
10
0
0
0
0
3
.5
255
436
Min
0.98
Typ
PF600.A01
850
Typ
Ty
2.2
48
48
12
20
1
Production Status
300
260
Typ
Consult Factory
86
89
0.99
Max
264
5.5
2.5
50.5
12.5
66
10
44
Max
600
500
59
14
50
2
Max
345
Page 1 of 4
mVp-p
mVp-p
Arms
Arms
Units
msec
Units
Vp-p
kVac
kVac
Vac
Vdc
Vdc
Vdc
Units
mA
sec
Vac
khrs
Hz
W
W
kHz
W
A
%
%
g