DS2482S-100+T&R Maxim Integrated Products, DS2482S-100+T&R Datasheet - Page 4
![IC I2C TO 1WIRE BRIDGE 8SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
DS2482S-100+T&R
Manufacturer Part Number
DS2482S-100+T&R
Description
IC I2C TO 1WIRE BRIDGE 8SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.DS2482S-100.pdf
(24 pages)
Specifications of DS2482S-100+T&R
Controller Type
I²C Bus Controller
Interface
I²C
Voltage - Supply
3.3 V, 5V
Current - Supply
750µA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Single-Channel 1-Wire Master
ELECTRICAL CHARACTERISTICS (continued)
(V
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Note 10: The input/output pins of the DS2482-100 do not obstruct the SDA and SCL lines if V
Note 11: The DS2482-100 provides a hold time of at least 300ns for the SDA signal (referred to the V
Note 12: The maximum t
Note 13: A fast-mode I
Note 14: C
Note 15: I
4
Input Capacitance
SCL Clock Frequency
Hold Time (Repeated) START
Condition (After this period, the
first clock pulse is generated.)
Low Period of the SCL Clock
High Period of the SCL Clock
Setup Time for a Repeated
START Condition
Data Hold Time
Data Setup Time
Setup Time for STOP Condition
Bus Free Time Between a STOP
and START Condition
Capacitive Load for Each Bus
Line
Oscillator Warmup Time
CC
_______________________________________________________________________________________
= 2.9V to 5.5V, T
PARAMETER
Operating current with 1-Wire write-byte sequence followed by continuously reading the Status Register at 400kHz in overdrive.
With standard speed, the total capacitive load of the 1-Wire bus should not exceed 1nF. Otherwise, the passive pullup on
threshold V
not exceed 300pF.
Active pullup guaranteed to turn on between V
Active or resistive pullup choice is configurable.
Except for t
these parameters is found to be off the typical value, it is safe to assume that all these parameters deviate from their typi-
cal value in the same direction and by the same degree.
These values apply at full load, i.e., 1nF at standard speed and 0.3nF at overdrive speed. For reduced load, the pulldown
slew rate is slightly faster.
Fall time high-to-low (t
All I
Applies to SDA, SCL, AD0 and AD1.
bridge the undefined region of the falling edge of SCL.
then be met. This is automatically the case if the device does not stretch the low period of the SCL signal. If such a device
does stretch the low period of the SCL signal, it must output the next data bit to the SDA line t
250 = 1250ns (according to the standard-mode I
Bus Specification Version 2.1 are allowed.
2
B
C communication should not take place for the max t
—Total capacitance of one bus line in pF. If mixed with high-speed-mode devices, faster fall times according to I
2
C timing values are referred to V
IL1
A
F1
= -40°C to +85°C.)
2
, all 1-Wire timing specifications and t
C bus device can be used in a standard-mode I
may not be reached in the available time. With overdrive speed, the capacitive load on the 1-Wire bus must
HD:DAT
F1
need only be met if the device does not stretch the low period (t
) is derived from PD
SYMBOL
t
t
t
OSCWUP
t
t
t
HD:STA
HD:DAT
SU:STO
SU:STA
SU:DAT
t
t
f
HIGH
t
LOW
SCL
BUF
C
C
B
I
IH(MIN)
(Note 9)
(Notes 11, 12)
(Note 13)
(Note 14)
(Note 15)
SRC
and V
IL1(MAX)
, referenced from 0.9 x V
2
C bus specification) before the SCL line is released.
IL(MAX)
APUOT
CONDITIONS
OSCWUP
and V
levels.
are derived from the same timing circuit. Therefore, if one of
IH1(MIN)
2
time following a power-on reset.
C bus system, but the requirement t
.
CC
to 0.1 x V
CC
CC
MIN
is switched off.
LOW
250
0.6
1.3
0.6
0.6
0.6
1.3
0
.
IH(MIN)
) of the SCL signal.
R(MAX)
TYP
of the SCL signal) to
SU:DAT
+ t
SU:DAT
MAX
400
400
100
0.9
10
≥ 250ns must
= 1000 +
UNITS
kHz
2
pF
μs
μs
μs
μs
μs
ns
μs
μs
pF
μs
C-