MAX5052AEUA Maxim Integrated Products, MAX5052AEUA Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX5052AEUA
Manufacturer Part Number
MAX5052AEUA
Description
Current Mode PWM Controllers w/Error Amplifier
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX5053BEUA.pdf
(13 pages)
Specifications of MAX5052AEUA
Number Of Outputs
1
Duty Cycle (max)
50 %
Output Current
1000 mA
Mounting Style
SMD/SMT
Package / Case
uSOP-8
Switching Frequency
262 KHz
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Synchronous Pin
No
Topology
Boost, Flyback
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX5052AEUA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Figure 1. Nonisolated Power Supply with Programmable Input-
Supply Start Voltage
the power dissipation across R1 even at the high end of
the universal AC input voltage (265VAC).
The MAX5052/MAX5053 include a cycle-by-cycle cur-
rent limit that turns off the gate drive to the external
MOSFET during an overcurrent condition. When using
the MAX5052 in the bootstrapped mode (if the power-
supply output is shorted), the tertiary winding voltage
drops below the 10V threshold causing the UVLO to
turn off the gate drive to the external power MOSFET.
This reinitiates a startup sequence with soft-start.
The MAX5052/MAX5053 have an input voltage
UVLO/EN pin. The threshold for this UVLO is 1.28V.
Before any operation can commence, the voltage on
this pin has to exceed 1.28V. The UVLO circuit keeps
the CPWM comparator, ILIM comparator, oscillator,
and output driver shut down to reduce current con-
sumption (see the Functional Diagram).
Use this UVLO function to program the input-supply
start voltage. For example, a reasonable start voltage
for a 36V to 72V telecom range might be set at 34V.
Calculate the divider resistor values, R2 and R3 (see
Figure 1) by using the following formulas:
The value of R3 is calculated to minimize the voltage-
drop error across R2 as a result of the input bias cur-
rent of the UVLO/EN pin. V
0V
C1
R1
V
Amplifier for Isolated/Nonisolated Power Supplies
SUPPLY
C2
C3
R
3
V
V
COMP
FB
IN
CC
≅
Current-Mode PWM Controllers with an Error
500
MAX5052
_______________________________________________________________________________________
×
UVLO/EN
NDRV
V
GND
I
ULR
UVLO IN
CS
Undervoltage Lockout
ULR2
R2
R3
2
MAX5052/MAX5053
(
×
V
= 1.28V, I
D1
V
Q1
IN
−
V
ULR
R4
T1
2
UVLO
D2
)
C4
= 50nA
V
OUT
R5
R6
(max). V
where the power supply must start.
where I
and V
In addition to the externally programmable UVLO func-
tion offered in both the MAX5052 and MAX5053, the
MAX5052 has an additional internal bootstrap UVLO
that is very useful when designing high-voltage power
supplies (see the Functional Diagram). This allows the
device to bootstrap itself during initial power-up. The
MAX5052 attempts to start when V
strap UVLO threshold of 21.6V.
During startup, the UVLO circuit keeps the CPWM com-
parator, ILIM comparator, oscillator, and output driver
shut down to reduce current consumption. Once V
reaches 21.6V, the UVLO circuit turns on both the CPWM
and ILIM comparators, as well as the oscillator, and
allows the output driver to switch. If V
9.7V, the UVLO circuit will shut down the CPWM com-
parator, ILIM comparator, oscillator, and output driver
returning the MAX5052/MAX5053 to the startup mode.
Normally V
transformer. However, at startup there is no energy
delivered through the transformer, hence, a special
bootstrap sequence is required. Figure 2 shows the
voltages on V
V
C1 charges through the startup resistor, R1, to an inter-
mediate voltage. At this point, the internal regulator
begins charging C2 (see Figure 1). The MAX5052 uses
only 45µA of the current supplied by R1, and the
remaining input current charges C1 and C2. The charg-
ing of C2 stops when the V
mately 9.5V, while the voltage across C1 continues
rising until it reaches the wake-up level of 21.6V. Once
V
begins switching the MOSFET and transfers energy to
the secondary and tertiary outputs. If the voltage on the
tertiary output builds to higher than 9.9V (the bootstrap
UVLO lower threshold), then startup has been accom-
plished and sustained operation commences.
IN
IN
and V
exceeds the bootstrap UVLO threshold, NDRV
ULR2
UVLO
IN
CC
IN
is the UVLO/EN wake-up threshold.
is the value of the input-supply voltage
is the UVLO/EN pin input current (50nA),
is derived from a tertiary winding of the
IN
are 0V. After the line voltage is applied,
R
and V
2
=
MAX5052 Startup Operation
V
IN
CC
V
−
ULR
V
Undervoltage Lockout
during startup. Initially, both
CC
ULR
2
MAX5052 Bootstrap
voltage reaches approxi-
2
×
IN
R
exceeds the boot-
3
IN
drops below
IN
7