LR645N3-P014 Supertex, LR645N3-P014 Datasheet
LR645N3-P014
Specifications of LR645N3-P014
Related parts for LR645N3-P014
LR645N3-P014 Summary of contents
Page 1
... This version can also be connected to an external depletion mode MOSFET for increased output current. When used in conjunction with Supertex depletion mode MOSFET DN2540N5, an output current 150mA is achieved. Package Options TO-92 TO-220 LR645N3-G LR645N5-G Pin Configurations Value 450V GATE NC 15.5V -55° ...
Page 2
... V ≥ V +1V applied to V AUX OUT - dB 120Hz, No Load - µV 0.01 to 100KHz - 10µ 400V OUT IN 13.2 V --- load 400 15V 1.0mA IN OUT 400 50V 3.0mA IN OUT ● Tel: 408-222-8888 ● www.supertex.com LR645 θ C/W) O 400* 170 70 78* pin OUT pin OUT ...
Page 3
... Applications requiring higher output current and/or a different output voltage can use the 8 pin adjustable version PWM IC C OUT ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 3 V OUT GATE GND + 5.0V – 12V AUX ● Tel: 408-222-8888 ● www.supertex.com LR645 ...
Page 4
... MOSFET for higher output current and external resistors for adjustable output voltage. As shown in Figure 2, the output current is increased to 150mA by using the Supertex 400V depletion-mode MOSFET DN2540. The maximum operating input voltage will be limited by the drain- to-source breakdown voltage of the external MOSFET, but cannot exceed the 450V rating of the LR645 ...
Page 5
... Figure 5: Typical Output Voltage vs Resistor Ratio DN2540N5 GATE V LR645LG C IN GND 250KΩ 8 2.5 3.0 Resistor Ratio (R2/R1) ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 5 5.0V 5.0V OUT REG + 0 to 150mA C OUT – 3.5 4.0 ● Tel: 408-222-8888 ● www.supertex.com LR645 ...
Page 6
... Dimension NOM - - (mm) MAX 1.75 0.25 JEDEC Registration MS-012, Variation AA, Issue E, Sept. 2005. * This dimension is not specified in the original JEDEC drawing. The value listed is for reference only. Drawings are not to scale. Supertex Doc. #: DSPD-8SOLGTG, Version H101708 Note 1 Seating Plane ...
Page 7
... Dimensions NOM - (inches) MAX .210 JEDEC Registration TO-92. * This dimension is not specified in the original JEDEC drawing. The value listed is for reference only. † This dimension is a non-JEDEC dimension. Drawings not to scale. Supertex Doc.#: DSPD-3TO92N3, Version D080408 Front View E E1 ...
Page 8
... JEDEC Registration TO-220, Variation AB, Issue K, April 2002. * This dimension is not specified in the original JEDEC drawing. The value listed is for reference only. † This dimension is a non-JEDEC dimension. Drawings not to scale. Supertex Doc. #: DSPD-3TO220N5, Version B090308 Φ Side View ...
Page 9
... Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship ...