LT1381CS#PBF Linear Technology, LT1381CS#PBF Datasheet - Page 5

• Manufacturer Part Number: LT1381CS#PBF
• Description: IC DVR/RCVR 5V RS232 DUAL 16SOIC
• Manufacturer: Linear Technology
• Type: Transceiverr

Specifications of LT1381CS#PBF

• Number Of Drivers/receivers: 2/2
• Protocol: RS232
• Voltage - Supply: 4.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PI FU CTIO S
C1
Capacitor Inputs. These pins require two external capaci-
tors C 0.1 F: one from C1
to C2
available and connected to pin C1
V
V
storage capacitor C 0.1 F, tied to ground or V
value capacitors may be used to reduce supply ripple. With
multiple transceivers, the V
into common capacitors.
V
V
storage capacitor C 0.1 F. Larger value capacitors may
be used to reduce supply ripple. With multiple transceiv-
ers, the V
capacitors.
TR2 OUT, TR1 OUT (Pin 7, 14): Driver Outputs at RS232
Voltage Levels. Driver output swing meets RS232 levels
for loads up to 3k. Slew rates are controlled for lightly
loaded lines. Output current capability is sufficient for
load conditions up to 2500pF. Outputs are in a high
impedance state when V
circuit protected from V
The RS232 line inputs of the LT1381 have on-chip protec-
tion from ESD transients up to 10kV. The protection
structures act to divert the static discharge safely to
system ground. In order for the ESD protection to function
effectively, the power supply and ground pins of the circuit
must be connected to ground through low impedances.
The power supply decoupling capacitors and charge pump
storage capacitors provide this low impedance in normal
application of the circuit. The only constraint is that low
ESR capacitors must be used for bypassing and charge
storage. ESD testing must be done with pins V
and GND shorted to ground or connected with low ESR
capacitors.
ESD PROTECTIO
+
+
–
–
+
U
(Pin 6): Negative Supply Output (RS232 Drivers).
, C1
(Pin 2): Positive Supply Output (RS232 Drivers).
2V
–
–(2V
. C1 may be deleted if a separate 12V supply is
CC
–
, C2
+
U
CC
– 2.1V. This pin requires an external charge
and V
– 3V). This pin requires an external charge
+
, C2
–
pins may be paralleled into common
–
U
(Pins 1, 3, 4, 5): Commutating
CC
–
+
+ 25V to V
+
U
= 0V. Outputs are fully short-
and V
to C1
–
–
+
.
pins may be paralleled
and another from C2
+
– 25V. Applying
CC
CC
, V
. Larger
+
, V
+
–
higher voltages will not damage the device if the over-
drive is moderately current limited. Short circuits on one
output can load the power supply generator and may
disrupt the signal levels of the other outputs. The driver
outputs are protected against ESD to 10kV for human
body model discharges.
REC2 IN, REC1 IN (Pins 8, 13): Receiver Inputs. These
pins accept RS232 level signals ( 30V) into a protected 5k
terminating resistor. The receiver inputs are protected
against ESD to 10kV for human body model discharges.
Each receiver provides 0.4V of hysteresis for noise immu-
nity. Open receiver inputs assume a logic low state.
REC2 OUT, REC1 OUT (Pins 9, 12): Receiver Outputs with
TTL/CMOS Voltage Levels. Outputs are fully short-circuit
protected to ground or V
TR2 IN, TR1 IN (Pins 10, 11): RS232 Driver Input Pins.
These inputs are TTL/CMOS compatible. Inputs should
not be allowed to float. Tie unused inputs to V
GND (Pin 15): Ground Pin.
V
decoupled with a 0.1 F ceramic capacitor close to the
package pin. Insufficient supply bypassing can result in
low output drive levels and erratic charge pump operation.
CC
0.1 F
(Pin 16): 5V Input Supply Pin. This pin should be
+
+
PROTECTED
LINE PINS
TO 10kV
0.1 F
0.1 F
RS232
0.1 F
+
+
1
2
3
4
5
6
7
8
TR2 OUT
REC2 IN
C1
V
C1
C2
C2
V
ESD Test Circuit
+
–
+
–
+
–
CC
LT1381
with the power ON or OFF.
REC1 OUT
REC2 OUT
TR1 OUT
REC1 IN
5V V
TR1 IN
TR2 IN
GND
CC
16
15
14
13
12
11
10
9
RS232
LINE PINS
PROTECTED
TO 10kV
LT1381 • ESD TC
LT1381
CC
+
.
0.1 F
5