ES1623 Chemtronics, ES1623 Datasheet - Page 4

• Manufacturer Part Number: ES1623
• Description: HD Silicon, 10 ounces, Aerosol
• Manufacturer: Chemtronics
• Type: Multi-Purposer

Specifications of ES1623

• Chemical Component: 1, 1-Difluoroethane/Dimethyl Polysiloxane/Isohexane/n-Hexane
• Dispensing Method: Aerosol
• Primary Type: Lubricant
• Weight: 10 Oz.

ITW CHEMTRONICS
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Clear, colorless liquid
Odor: Mild hydrocarbon solvent
pH: NA
Vapor Pressure: 239 mmHg @ 68F (liquid)
Percent Volatile: 97%
SECTION 10: STABILITY AND REACTIVITY
Stability: This product is stable.
Products of Decomposition: Thermal decomposition may release carbon monoxide, carbon dioxide and incompletely burned hydrocarbons.
Hazardous Polymerization: Will not occur. Conditions to avoid: NA
SECTION 11: TOXICOLOGICAL INFORMATION
Inhalation:
1,1-difluoroethane *
Skin:
Not available
*Information from Dupont.
Cancer Information: No ingredients listed as human carcinogens by NTP or IARC
Reproductive effects: none
SECTION 12: ECOLOGICAL INFORMATION
Avoid runoff into storm sewers and ditches which lead to waterways. Water runoff can cause environmental damage.
REPORTING
US regulations require reporting spills of this material that could reach any surface waters. The toll free number for the US Coast Guard National Response Center is:
1-800-424-8802
SECTION 13: DISPOSAL CONSIDERATIONS
Dispose of in accordance with all federal, state and local regulations. Water runoff can cause environmental damage.
SECTION 14: TRANSPORTATION INFORMATION
Air: Aerosols flammable
Ground: Consumer Commodity
SECTION 15: REGULATORY INFORMATION
SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To- Know
Act of 1986 (40CFR372).
n-Hexane
This information should be included on all MSDSs copied and distributed for this material.
TOXIC SUBSTANCES CONTROL ACT (TSCA). All ingredients of this product are listed on the TSCA Inventory.
WHMIS: Class A; Class B5; Class D2B
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of the information required by the CPR.
SECTION 16: OTHER INFORMATION
Product is a Level 3 aerosol. Do not puncture or incinerate containers. Normal ventilation for standard manufacturing practices is usually adequate. Local exhaust
should be used when large amounts are released.
To the best of our knowledge, the information contained herein is accurate. However, all materials may present unknown hazards and should be used with caution. In
particular, improper use of our products and their inappropriate combination with other products and substances may produce harmful results which cannot be
anticipated. Final determination of the suitability of any material is the sole responsibility of the user. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that may exist.
Incompatibility; Do not mix powdered alkali and alkaline earth metals or strong oxidizing agents.
Shipping Name
ORM-D
Proper
®
Rat ALC
Conditions to Avoid: Do not spray near open flames, red hot surfaces or other sources of ignition.
Teratogenic effects: none
383,000 ppm/4hrs
UN Number
NA
UN 1950
Class
2.1
ORM-D
Sub.
Risk
CAS# 110-54-3
NA
Page 2 of 2
NA
Mutagenic effects: none
Pkg.
Group
NA
NA
Solubility in Water: Negligible
Specific Gravity:
Evaporation Rate: <1 (Butyl acetate=1)
Vapor Density: 3 (isohexanes)
Boiling Point: 122º F
Flammable
Gas
ORM-D
Ingestion:
Eyes:
Mild irritant
1,1-difluoroethane *
Hazard
Label
0.67 @ 68F
Rat ALD
Pkg.
Instr.
203
Pkg.
Auth.
(50ºC)
0.1-3.0%
MSDS # 1623
75/150 kg
173.306
>1500 mg/kg
Quantity
Max.