MAX3319ECAE+ Maxim Integrated Products, MAX3319ECAE+ Datasheet - Page 10

• Manufacturer Part Number: MAX3319ECAE+
• Description: IC TXRX RS232 460KBPS 16-SSOP
• Manufacturer: Maxim Integrated Products
• Type: Transceiverr

Specifications of MAX3319ECAE+

• Number Of Drivers/receivers: 2/2
• Protocol: RS232
• Voltage - Supply: 2.25 V ~ 3 V
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP
• Propagation Delay Time Ns: 0.175 us
• Operating Supply Voltage: 2.5 V to 3 V
• Supply Current: 0.3 mA
• Operating Temperature Range: 0 C to + 70 C
• Data Rate: 460 Kbps
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

By connecting FORCEON to INVALID, the MAX3318E/
MAX3319E shut down when no valid receiver level is
detected and wake up when a valid receiver level is
detected.
A system with AutoShutdown Plus may need time to
wake up. Figure 5 shows a circuit that forces the trans-
mitters on for 100ms, allowing enough time for the other
system to realize that the MAX3318E/MAX3319E is
awake. If the other system outputs valid RS-232 signal
transitions within that time, the RS-232 ports on both
systems remain enabled.
If direct software control is desired, use INVALID to
indicate DTR or ring indicator (RI) signal. This can be
used to connect a hand-held device to a PC. One
example is using the Hot Sync™ function on a personal
digital assistant (PDA). The transmitter and receiver
signals (T_OUT and R_IN) are used for communication,
while INVALID causes a change of state on RI. The
change of state on RI will trigger an interrupt on the PC
and allow communication to begin between the device
and the PC. This eliminates the need for the PC to poll
constantly the receiver or transmitter lines to determine
if the device is connected.
All the pins on the MAX3316E–MAX3319E are protect-
ed against ESDs encountered during handling and
assembly. The driver outputs and receiver inputs have
extra protection against static electricity. Maxim’s engi-
neers have developed state-of-the-art structures to pro-
tect these pins against ESD of ±15kV without damage.
The ESD structures withstand high ESD in all states:
normal operation, shutdown, and powered down. After
an ESD event, Maxim’s E versions keep working without
latchup, whereas competing products can latch and
must be powered down to remove latchup.
ESD protection can be tested in various ways; the trans-
mitter outputs and receiver inputs of the product family
are characterized for protection to the following limits:
• ±15kV using the Human Body Model
• ±8kV using the IEC 1000-4-2 Contact Discharge
• ±15kV using IEC 1000-4-2 Air-Gap method
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
±15kV ESD-Protected, 2.5V, 1µA, 460kbps,
RS-232 Compatible Transceivers
Hot Sync is a trademark of 3Com.
10
method
______________________________________________________________________________________
(MAX3318E/MAX3319E)
±15kV ESD Protection
Connecting to the PC
ESD Test Conditions
Figure 6a shows the Human Body Model, and Figure 6b
shows the current waveform it generates when dis-
charged into low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.5kΩ resistor.
Figure 3a. INVALID Functional Diagram, INVALID Low
Figure 3b. INVALID Functional Diagram, INVALID High
Figure 4a. Receiver Positive/Negative Thresholds for INVALID
+0.3V
-0.3V
+2.7V
-2.7V
R_IN
R_IN
INVALID DEASSERTED IF ANY RECEIVER INPUT HAS BEEN BETWEEN +2.7V AND -2.7V
FOR LESS THAN 30µs.
INVALID ASSERTED IF ALL RECEIVER INPUTS ARE BETWEEN +0.3V AND -0.3V FOR
AT LEAST 30µs.
+2.7V
+0.3V
-0.3V
-2.7V
0
INDETERMINATE
INDETERMINATE
INVALID HIGH
INVALID HIGH
INVALID LOW
Human Body Model
TIMER
TIMER
30µs
30µs
R
R
INVALID
INVALID