DS90C401M/NOPB National Semiconductor, DS90C401M/NOPB Datasheet - Page 4
![IC DRV LVDS DUAL DIFF SGNL 8SOIC](/photos/6/87/68721/ds90c401m_nopb_sml.jpg)
DS90C401M/NOPB
Manufacturer Part Number
DS90C401M/NOPB
Description
IC DRV LVDS DUAL DIFF SGNL 8SOIC
Manufacturer
National Semiconductor
Type
Driverr
Datasheet
1.DS90C401MNOPB.pdf
(11 pages)
Specifications of DS90C401M/NOPB
Number Of Drivers/receivers
2/0
Protocol
RS644
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Supply Current
14mA
Supply Voltage Range
4.5V To 5.5V
Driver Case Style
SOP
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Device Type
Differential Line Driver
Esd Hbm
3.5kV
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*DS90C401M
*DS90C401M/NOPB
DS90C401M
*DS90C401M/NOPB
DS90C401M
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS90C401M/NOPB
Manufacturer:
Cirrus
Quantity:
133
Part Number:
DS90C401M/NOPB
Manufacturer:
NS/国半
Quantity:
20 000
www.national.com
Applications Information
LVDS drivers and receivers are intended to be primarily used
in an uncomplicated point-to-point configuration as is shown
in Figure 4. This configuration provides a clean signaling
environment for the quick edge rates of the drivers. The
receiver is connected to the driver through a balanced media
which may be a standard twisted pair cable, a parallel pair
cable, or simply PCB traces. Typically, the characteristic
impedance of the media is in the range of 100Ω. A termina-
tion resistor of 100Ω should be selected to match the media,
and is located as close to the receiver input pins as possible.
The termination resistor converts the current sourced by the
driver into a voltage that is detected by the receiver. Other
configurations are possible such as a multi-receiver configu-
ration, but the effects of a mid-stream connector(s), cable
stub(s), and other impedance discontinuities as well as
ground shifting, noise margin limits, and total termination
loading must be taken into account.
The DS90C401 differential line driver is a balanced current
source design. A current mode driver, generally speaking
has a high output impedance and supplies a constant cur-
rent for a range of loads (a voltage mode driver on the other
hand supplies a constant voltage for a range of loads).
Current is switched through the load in one direction to
produce a logic state and in the other direction to produce
the other logic state. The typical output current is mere 3.4
mA, a minimum of 2.5 mA, and a maximum of 4.5 mA. The
FIGURE 5. Driver Output Levels
4
current mode requires (as discussed above) that a resistive
termination be employed to terminate the signal and to com-
plete the loop as shown in Figure 4. AC or unterminated
configurations are not allowed. The 3.4 mA loop current will
develop a differential voltage of 340 mV across the 100Ω
termination resistor which the receiver detects with a 240 mV
minimum differential noise margin neglecting resistive line
losses (driven signal minus receiver threshold (340 mV –
100 mV = 240 mV)). The signal is centered around +1.2V
(Driver Offset, V
Figure 5. Note that the steady-state voltage (V
peak swing is twice the differential voltage (V
typically 680 mV.
The current mode driver provides substantial benefits over
voltage mode drivers, such as an RS-422 driver. Its quies-
cent current remains relatively flat versus switching fre-
quency. Whereas the RS-422 voltage mode driver increases
exponentially in most case between 20 MHz–50 MHz. This
is due to the overlap current that flows between the rails of
the device when the internal gates switch. Whereas the
current mode driver switches a fixed current between its
output without any substantial overlap current. This is similar
to some ECL and PECL devices, but without the heavy static
I
>
cations for the driver are a tenfold improvement over other
existing RS-422 drivers.
CC
80% less current than similar PECL devices. AC specifi-
requirements of the ECL/PECL designs. LVDS requires
OS
) with respect to ground as shown in
10001310
SS
OD
) peak-to-
) and is