TBCR Bogen Communications, Inc., TBCR Datasheet - Page 2

• Manufacturer Part Number: TBCR
• Description: Tile Bridge Support FOR HSCF
• Manufacturer: Bogen Communications, Inc.

Specifications of TBCR

• Dimensions: 17"(W) × 11⁄8"(H) × 24"(D)
• Mounting Type: Flush
• Lead Free Status / Rohs Status: RoHS Compliant part
• For Use With: Speaker

Specifications subject to change without notice.
© 2004 Bogen Communications, Inc.
Part No. 54-2093-01B 0401
The TBCR is warranted to be free from defects in material or workmanship for five (5) years from the date of sale to the original purchaser.Any part of the prod-
uct covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product
is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight pre-
paid.This warranty does not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or
have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO
THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition,
whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be liable for special, incidental or
consequential damages (including, but not limited to, loss of profits, loss of data or loss of use damages) arising out of the manufacture, sale or supplying of prod-
ucts, even if Bogen has been advised of the possibility of such damages or losses. Some States do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above limitation or exclusion may not apply to you.This warranty gives you specific legal rights, and you may also have other rights which vary
from State to State.
Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call 201-934-8500. The parts and
labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and
labor charges will be at the owner's expense. All returns require a Return Authorization number.
RETROFITTING INTO EXISTING SHEETROCK CEILINGS
B. For 24" Centers Joist Spacing
1. Determine the location laterally in the joist space for the speaker
2.
3.
The support ring in this application provides additional stiffening of the
opening and can be used as a template to outline the hole.
•
•
1. Determine an appropriate location in ceiling, taking into account
2.
3.
4.
and move the support ring accordingly.
Note: Support Ring must be fully within the joist space for
the speaker to mount correctly. Also, check that there is
sufficient vertical space above the ring to fit the particular
speaker being used.
Nail the TBCR (as it comes, do not remove breakaway tabs) to
the bottom of the joist.
After the sheetrock is up and the hole routed, follow the speaker’s
installation instructions to complete the installation.
The edge of this hole must be a minimum of 1¼" away from any
joists to ensure it will not interfere with the clamps.
Check that there is sufficient vertical space above the ring to fit the
particular speaker being used. Before cutting the full hole, use a
smaller exploratory hole to determine joist height and to check
for obstructions.
joists and other obstructions. Use the support ring as a template
to outline the hole and cut the opening.
Using a pair of cutting pliers, snip the tabs bridging the gap in the
ring.
Twist the ring into the hole. The ring is split to allow it to be
"threaded" though the hole.The bent ends of the ears must point
up. Align the ring with the hole.
Follow the speaker’s installation instructions to complete the
installation.
IMPORTANT
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel. [phone], Fax: [phone], www.bogen.com