LTC490IS8 Linear Technology, LTC490IS8 Datasheet - Page 7
![IC TXRX RS485 LOWPWR DIFF 8-SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LTC490IS8
Manufacturer Part Number
LTC490IS8
Description
IC TXRX RS485 LOWPWR DIFF 8-SOIC
Manufacturer
Linear Technology
Type
Transceiverr
Datasheet
1.LTC490CN8PBF.pdf
(12 pages)
Specifications of LTC490IS8
Number Of Drivers/receivers
1/1
Protocol
RS422, RS485
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC490IS8
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC490IS8#PBF
Manufacturer:
LT
Quantity:
6 500
Company:
Part Number:
LTC490IS8#PBF
Manufacturer:
LTC
Quantity:
1 067
Part Number:
LTC490IS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC490IS8#TRPBF
Manufacturer:
LT
Quantity:
20 000
APPLICATIO S I FOR ATIO
less flexible, more bulky, and more costly than twisted
pairs. Many cable manufacturers offer a broad range of
120 cables designed for RS485 applications.
Losses in a transmission line are a complex combination
of DC conductor loss, AC losses (skin effect), leakage and
AC losses in the dielectric. In good polyethylene cables
such as the Belden 9841, the conductor losses and
dielectric losses are of the same order of magnitude,
leading to relatively low overall loss (Figure 7).
When using low loss cables, Figure 8 can be used as a
guideline for choosing the maximum line length for a given
data rate. With lower quality PVC cables, the dielectric loss
factor can be 1000 times worse. PVC twisted pairs have
Figure 8. RS485 Cable Length Specification. Applies for 24
Gauge, Polyethylene Dielectric Twisted Pair
Figure 7. Attenuation vs Frequency for Belden 9841
0.1
1.0
10
10k
100
10
1k
0.1
10k
U
FREQUENCY (MHz)
1.0
100k
DATA RATE (bps)
U
10
1M
W
2.5M
LTC490 • F07
LTC490 • F08
100
10M
U
terrible losses at high data rates (>100kbs), and greatly
reduce the maximum cable length. At low data rates
however, they are acceptable and much more economical.
Cable Termination
The proper termination of the cable is very important.
If the cable is not terminated with its characteristic
impedance, distorted waveforms will result. In severe
cases, distorted (false) data and nulls will occur.
A quick look at the output of the driver will tell how well the
cable is terminated. It is best to look at a driver connected
to the end of the cable, since this eliminates the possibility
of getting reflections from two directions. Simply look at
the driver output while transmitting square wave data. If
the cable is terminated properly, the waveform will look
like a square wave (Figure 9). If the cable is loaded
excessively (47 ), the signal initially sees the surge
impedance of the cable and jumps to an initial amplitude.
The signal travels down the cable and is reflected back out
of phase because of the mistermination. When the re-
flected signal returns to the driver, the amplitude will be
lowered. The width of the pedestal is equal to twice the
electrical length of the cable (about 1.5ns/foot). If the
Rt = 120
Rt = 470
Rt = 47
DX
DRIVER
Figure 9. Termination Effects
PROBE HERE
Rt
RECEIVER
LTC490
LTC490 • F09
RX
7
490fb