BPA60 Bogen Communications, Inc., BPA60 Datasheet

BPA60

Manufacturer Part Number

BPA60

Description

Amplifier; 60 W (RMS); 20 Hz to 20 kHz; 85 dB (Below Rated Output); 19 lbs.

Manufacturer

Bogen Communications, Inc.

Datasheet

1.BPA60.pdf (2 pages)

Specifications of BPA60

Controls

Illuminated On⁄Off Power Switch (Front Panel), Input Level Control, Circuit Breaker Reset, Lo Cut Filter Switch (Rear Panel)

Dimensions

15-1⁄4 in. W x 3-1⁄2 in. H x 8 in. D

Frequency Response

20 Hz to 20 kHz

Hum And Noise

85 dB (Below Rated Output)

Mounting Type

Rack Panel Kit

Power Consumption

180 W @ 120 VAC, 60 Hz

Power Output

60 W (RMS)

Protection

Transient Protection Diodes, Electrical Circuit Breaker, 221°F (105°C) Thermostat

Sensitivity

High Impedance, 300 mV, Low Impedance Balanced, with Optional Transformer, 75 mV

Standards

UL Listed, CSA Certified

Weight, Shipping

19 lbs.

Current page: 1 of 2
Download datasheet (377Kb)

Power Amplifier

Description

Features

• 60 watts rated power

• Distortion less than 2% THD

• Transient protection diodes

• Frequency response -2dB from 20Hz to 20kHz

• Multiple output voltages/impedances available

• Resettable circuit breaker; thermally protected

• UL and CSA listed

The Bogen BPA60 solid-state power amplifier has

been designed to fulfill the power amplification

requirements of professional and commercial sound

systems. The Model BPA60 supplies 60 watts RMS

output. Total harmonic distortion is less than 2% at

rated output from 50Hz to 5kHz.

Input impedances for the BPA60 are: high-impedance

(50k-ohms) unbalanced; and low-impedance (500/600

ohms, balanced or unbalanced) with accessory trans-

former Model TL600. Line-bridging may be achieved

with accessory transformer Model TL100. Hum and

noise are at least 85dB below rated output.

The BPA60 amplifier may be driven from an amplifier

that provides a 25- or 70-volt output. Output imped-

ances for the BPA60 are: 8-ohm/25V, 16-ohm, 25VCT

and 70V. Output regulation is better than 2dB from

no load to full load.

Model BPA60

The BPA60 amplifier is thermally protected to prevent

damage due to excessive temperatures; however, it

will deliver the full rated output continuously, even at

+130° F (+55° C). Additional protection is provided

by transient protection diodes and an electrical circuit

breaker.

An illuminated on/off power switch is located on the

front panel. An input level control, circuit breaker

reset, lo-cut filter switch, and auxiliary receptacle are

located on the rear panel. A rack panel kit (RPK53) is

available for mounting the amplifier in a 19-inch equip-

ment rack.

Specifications subject to change without notice.

Part No. 54-7609-06R2 Printed in U.S.A. 0109

Related parts for BPA60

BPA60 Summary of contents

Page 1

... Model TL600. Line-bridging may be achieved with accessory transformer Model TL100. Hum and noise are at least 85dB below rated output. The BPA60 amplifier may be driven from an amplifier that provides a 25- or 70-volt output. Output imped- ances for the BPA60 are: 8-ohm/25V, 16-ohm, 25VCT and 70V ...

Page 2

... Operating Temperature Range: Auxiliary Receptacle (not switched): *This receptacle will be grounded only if the power amplifier has been grounded properly. The amplifier shall be a Bogen BPA60 power amplifier or approved equivalent. It shall be of solid-state con- struction and shall have integrated circuits, silicon transistors and diodes to provide for continuous high- Architect quality sound ...

Related keywords

BPA60 datasheet
BPA60 data sheet
BPA60 pdf datasheet
BPA60 component
BPA60 part
BPA60 distributor
BPA60 RoHS
BPA60 datasheet download