PBB BANNER ENGINEERING, PBB Datasheet
PBB
Specifications of PBB
Available stocks
Related parts for PBB
PBB Summary of contents
Page 1
MULTI-BEAM Compact modular self-contained photoelectric sensing controls 1.6" (40 mm) 4.5" (114 mm) 1/2" – 14 NPSM Conduit Entrance 5 mm (#10) Screw Clearance (4) (30.0 mm) Printed in USA ® Sensors Status Indicator LED (except emitters) Access to Sensitivity ...
Page 2
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. ...
Page 3
MULTI-BEAM Sensors E71083 Banner MULTI-BEAM ® sensors are compact modular self con- tained photoelectric switches. Each MULTI-BEAM consists of three components: scanner block, power block, and logic module. The scanner block contains the complete modulated photoelectric amplifier as well as ...
Page 4
Selection of MULTI-BEAM Components MULTI-BEAM sensors are made up of three components: scanner block, power block, and logic module. This is true for all MULTI- BEAMs with the exception of opposed mode emitter units which require only a power block ...
Page 5
... PBT PBT2 PBP PBT-1 PBT48 PBP48 PBT48-1 PBD-2 PBD PBD-1 PBA PBAQ PBAT PBO PBAM PBA-1 PBB PBBT PBOB PBB-1 Logic Modules Model LM1 LM3 LM5 LM5R LM5-14 LM5T LM4-2 LM4-2NR LM8-1 LM8A LM6-1 LM8 LM2 LM10 LMT 2-wire Systems (pages 24 through 29) ...
Page 6
... Systems (pages 24 through 29) Power Blocks Model 2PBD 2PBA 2PBB 2PBR 2PBR2 Logic Modules Model 2LM3 2LM5 2LM5R 2LM5-14 2LM5T 2LM4-2 LMT MULTI-BEAM Other Systems Edgeguide Systems (data sheet 03506) MULTI-BEAM 3- & 4-WIRE SCANNER BLOCKS DESCRIPTION MULTI-BEAM 3- & 4-wire scanner blocks offer a complete comple- ment of sensing modes ...
Page 7
MULTI-BEAM Sensing Mode OPPOSED Mode OBJECT 3- & 4-wire Scanner Blocks Models Excess Gain SBE/SBR1: this opposed pair has the highest gain available response. SBED/SBRD1: fast response and small effective beam; will detect objects as small as ...
Page 8
MULTI-BEAM Sensing Mode RETROREFLECTIVE Mode RETRO TARGET OBJECT NOTE: for detailed information on available retroreflective materials, see the Banner product catalog & 4-wire Scanner Blocks Models Excess Gain SBLV1: visible beam makes alignment very easy, and is the ...
Page 9
MULTI-BEAM Sensing Mode DIFFUSE Mode OBJECT APPLICATION NOTE general rule regarding background objects in diffuse sens- ing, verify that the distance to the nearest background object is at least three times the distance from the sensor to the ...
Page 10
MULTI-BEAM Sensing Mode CONVERGENT Mode OBJECT Counting radiused products 10 3- & 4-wire Scanner Blocks Models Excess Gain SBCV1: .06-inch (1.5mm) dia. visible red spot, for precise positioning, edge-guiding, & small parts detection. Sensor-to-product distance must be consistent. Some products ...
Page 11
MULTI-BEAM Sensing Mode OPPOSED FIBER OPTIC Mode (glass fiber optics) OBJECT FIBER OPTIC Mode (glass fiber optics) HIGH-POWER SCANNER BLOCK OPPOSED MODE OBJECT DIFFUSE MODE OBJECT For complete information on glass fiber optic assemblies and accessories, see product catalog. 3- ...
Page 12
MULTI-BEAM Sensing Mode FIBER OPTIC Mode (glass fiber optics) HIGH-SPEED SCANNER BLOCK OPPOSED MODE OBJECT RETROREFLECTIVE MODE RETRO TARGET OBJECT DIFFUSE MODE OBJECT Fiber optics are often used to sense small parts. Small parts or narrow profiles which move at ...
Page 13
MULTI-BEAM Sensing Mode FIBER OPTIC Mode (glass fiber optics) VISIBLE RED LIGHT SOURCE OPPOSED MODE OBJECT RETROREFLECTIVE MODE RETRO TARGET OBJECT DIFFUSE MODE OBJECT Scanner block model SBFV1 supplies visible red light to the emitter half of a glass fiber ...
Page 14
MULTI-BEAM Sensing Mode AMBIENT LIGHT RECEIVER NOTE: MULTI-BEAM ambient light re- ceivers do not have the Alignment Indicating Device (AID™) signal strength feature. The alignment indicator is "ON" steadily when enough light is sensed. FIBER OPTIC AMBIENT LIGHT RECEIVER (glass ...
Page 15
MULTI-BEAM DC Models PBT Input 30V dc at less than 60mA (current draw depends on scanner block used). 10% max. ripple. Output: one open-collector NPN transistor (sinks current to negative side of power supply). 250mA maximum. On state ...
Page 16
MULTI-BEAM DC Models These are power blocks for emitter scanner blocks only (models SBE, SBED, SBEX, SBEV, SBEXD, SBEF, SBEXF). Emitter assemblies do not require logic modules. PBT-1 Input 30V dc at less than 60mA (current draw depends ...
Page 17
... Vac MA4L Latch NOTE: MULTI-BEAM dc power blocks cannot be wired in series. MULTI-BEAM AC Models PBA Input: 105 to 130V ac, 50/60Hz. PBB Input: 210 to 250V ac, 50/60Hz. PBD Input 28V ac, 50/60Hz. PBD-2 Input 13V ac, 50/60Hz. Output: SPST solid-state switch for ac, 3/4 amp maximum (derated to 1/2 amp at 70 degrees C). ...
Page 18
... Power block models PBAT and PBBT have an isolated solid-state output switch which may be used to switch either ac or dc. The switch is rated at 100mA maximum, and there is no capacity for inrush result, these power blocks usually should not be used to switch ac inductive loads. However, 100mA is enough capacity to switch many inductive dc loads like small relays and solenoids ...
Page 19
... (See Specifications) PBA PBB PBD PBD2 PBAQ 3 4 LOAD 1 2 Functional Schematics Hookup Emitter MULTI-BEAM emitter-only ac power blocks connect directly across the ac line, as shown. Emitter models: SBE, SBED, SBEX, SBEV, SBEXD, SBEF, and SBEXF (See Specifications) PBA-1 PBB-1 PBD ...
Page 20
... The total voltage drop across the (See Specifications) series will be the sum of the individual voltage drops across each power block (approximately 3 volts per block). With most loads more power blocks may be wired in series PBA PBB PBD PBD2 PBAQ 3 4 LOAD ...
Page 21
MULTI-BEAM Functional Schematic RESPONSE TIME: response time will be that for the scanner block (plus power block) plus the programmed delay (if the logic includes a delay function). Model and Function LM1 on-off OUTPUT SIGNAL LM2 alternate action OUTPUT SIGNAL ...
Page 22
MULTI-BEAM Model and Function LM4-2NR one-shot (non-retriggerable) Pulse Pulse Pulse OUTPUT SIGNAL Setable time range second. LM5 on-delay Delay OUTPUT SIGNAL Setable time range: 1 seconds. LM5R off-delay Hold Hold OUTPUT SIGNAL Setable time range: ...
Page 23
MULTI-BEAM Model and Function LM8 repeat cycler Delay Hold Delay Hold Delay Hold OUTPUT SIGNAL Setable time range: 1 seconds. LM8-1 delayed one-shot Delay Hold Delay Hold OUTPUT SIGNAL Setable time range: 1 seconds. LM8A on-delay ...
Page 24
MULTI-BEAM 2-wire Sensors 2-wire MULTI-BEAM Functional Schematic, 2-wire MULTI-BEAM MULTI-BEAM 2-Wire Scanner Blocks SPECIFICATIONS SUPPLY VOLTAGE: connections are made via a 2-wire power block (see page 27). RESPONSE TIME: 10 milliseconds ON and OFF (3000 operations per minute). NOTE: a ...
Page 25
... The SBE emiter uses a 3 & 4 wire power block. Powerblocks for use with SBE include models PBA-1, PBB-1, PBD-1, PBT-1, and PBT48-1 (see pages 16 and 19 for information on these powerblocks). ...
Page 26
MULTI-BEAM Sensing Mode OBJECT DIFFUSE Mode FIBER OPTIC Mode (glass fibers) OPPOSED MODE OBJECT RETROREFLECTIVE MODE RETRO TARGET OBJECT DIFFUSE MODE OBJECT 26 2-wire Scanner Blocks Models Excess Gain 1000 2SBD1 E 2SBD1 X C 100 Range: ...
Page 27
... MULTI-BEAM MULTI-BEAM 2-wire power block models 2PBA, 2PBB, and 2PBD contain a low voltage power supply which utilizes a unique circuit to take a very small leakage current through the load and convert it to the dc power required to run the scanner block and logic module. They also contain the solid-state switch that operates the load, and a transient suppression circuit to prevent false operation from high voltage spikes on the incoming line ...
Page 28
... MULTI-BEAM's 0.1 second power-up delay may cause a momentary drop-out of the load (See Specifications) 2PBA 2PBB 2PBD 1 2 LOAD Photoelectric Latch with Manual Reset 1CR relay will latch "on" whenever the 2-wire MULTI-BEAM output is energized. 1CR is reset ...
Page 29
MULTI-BEAM SPECIFICATIONS, 2-WIRE LOGIC MODULES: specifications for 2-wire logic modules are identical to those for 3- and 4-wire logic modules (see page 21). Model and Function 2LM3 on-off OUTPUT SIGNAL 2LM4-2 one-shot Hold Pulse Pulse OUTPUT SIGNAL Setable time range: ...
Page 30
MULTI-BEAM Accessories Upper Covers (Lens Assemblies) An upper cover consists of the optical element for the MULTI-BEAM which is built into a gasketed cover for the upper portion of the scanner block. Upper covers may be ordered as replacement parts ...
Page 31
MULTI-BEAM Accessories Mounting Brackets SMB700 Model (right general-purpose two-axis mount- ing bracket that is supplied with a cable gland assembly which is used to attach the MULTI-BEAM wiring base to the bracket. The gland assembly is threaded through ...
Page 32
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products ...