E4416A Agilent Technologies Test Equipment, E4416A Datasheet - Page 4

• Manufacturer Part Number: E4416A
• Description: Meter, Power
• Manufacturer: Agilent Technologies Test Equipment
• Type: Wattr

4
Trigger
Sources:
Time resolution:
Delay range:
Delay resolution:
Hold-off:
Internal trigger:
Latency is defined as the delay between the applied RF
crossing the trigger level and the meter switching into
the triggered state.
External trigger range:
BNC connector; rising or falling edge triggered; input
impedance > 1 kW.
Trigger out:
(high > 2.4 V, low < 0.4 V) and uses a BNC connector
Sampling characteristics
Sampling rate:
Sampling technique:
Rear panel inputs/outputs
Recorder output(s):
impedance, BNC connector. Two outputs are available
on E4417A (channels A and B).
Remote input/output:
RS-232/422 interface:
cation with an external controller. Male plug 9-pin
D-subminiature connector.
Trigger in:
ments, BNC connector.
Range:
Range:
Resolution:
Level accuracy:
Resolution:
Latency:
TTL output:
TTL input:
Connector type:
TTL output:
TTL input:
defined limit.
cycle.
Accepts a TTL signal for initiating measure-
Output provides TTL compatible levels
1% of selected value
0.1 dB
500 ns ± 100 ns
used to signal when mea
surement has exceeded a
initiates zero and calibration
high = 4.8 V max;
high = 3.5 V min, 5 V max;
Analog 0 to 1 V, 1 kW output
Internal, External TTL,
GPIB, RS232/422,
50 ns
±1.0 s
50 ns for delays < ±50 ms;
otherwise 200 ns
1 us to 400 ms
(minmum of 100 ns)
-20 to +20 dBm
±0.5 dB
20 Msamples/second
Continuous sampling
RJ-45 series shielded modu
lar jack assembly.
low = 0.2 V max.
low = 1 V max, -0.3 V min.
Serial interface for communi-
High > 2.0 V, Low < 0.8 V;
Trigger out:
with external equipment, BNC connector.
Ground:
connection
Line power
Remote programming
Interface:
IEC-625. RS-232 and RS-422 serial interfaces supplied as
standard
Command language:
commands
GPIB compatibility:
RL1, PP1, DC1, DT1, C0.
Environmental specifications
Operating environment
Storage conditions:
Regulatory information
Electromagnetic compatibility:
conforms with the protection requirements of European
Council Directive 89/336/EEC for Electromagnetic
Compatibility (EMC). The conformity assessment
requirements have been met using the technical
Construction file route to compliance, using EMC test
specifications EN 55011:1991 (Group 1, Class A) and EN
50082-1:1992. In order to preserve the EMC performance
of the product, any cable which becomes worn or dam-
aged must be replaced with the same type and specifica-
tion.
Product safety:
ments of European Council Directive 73/23/EEC, and
meets the following safety standards:
IEC 61010-1(1990) + A1 (1992) + A2 (1995) /
EN 61010-1 (1993)
IEC 825-1 (1993) / EN 60825-1 (1994)
Canada / CSA C22.2 No. 1010.1-93
Input voltage range
Input frequency range
Power requirement
Temperature
Maximum humidity
Minimum humidity
Maximum altitude
Storage temperature
Non-operating maximum
humidity:
Non-operating maximum
altitude:
Binding post accepts 4 mm plug or bare wire
GPIB interface operates to IEEE 488.2 and
Outputs a TTL signal for synchronizing
This product conforms to the require-
SH1, AH1, T6, TE0, L4, LE0, SR1,
SCPI standard interface
85 to 264 Vac,
automatic selection
47 to 440 Hz
approximately 50 VA
(14 Watts)
0° to 55 °C
95% at 40 °C,
(non-condensing)
15% at 40 °C
3,000 meters
(9,840 feet)
-20 to +70°C
90% at 65 °C
(non-condensing)
15,420 meters
(50,000 feet)
This product