ELC-ACPGMXFR Eaton / Control Automation, ELC-ACPGMXFR Datasheet - Page 3

• Manufacturer Part Number: ELC-ACPGMXFR
• Description: ACCESSORY; ELC CONTROLLER PROGRAM TRANSFER MODULE
• Manufacturer: Eaton / Control Automation
• Type: Programmingr

Specifications of ELC-ACPGMXFR

• Brand/series: ELC
• Primary Type: Option
• For Use With: Micro Controllers

3.6 Estimation of Read/Write Operating Time
The password composes of 4 bytes. Each byte is an ASCII consisting of ‘0’~’9’, ‘A’~’Z’. ‘a’ ~’z’. ELC and ACPGMXFR verify
password with case-sensitive. Below is ASCII table.
4
ACPGMXFR Internal
memory error
Incompatible model or
syntax error
Operation error – unable to
write
Operation error – unable to
read
Password verify error
ERASE completed
5
6
ASCII
ASCII
ASCII
ELC-PB
ELC-PC/PA/PH
HEX
HEX
HEX
conditions:
ACPGMXFR will show error or warning status by Indicator LED. Below is the summary:
If ERR LED is always ON or blinking. Please refer to section 4.
Disconnect ACPGMXFR or power down the ELC when the operation in progress. It will cause some unexpected
ACPGMXFR data will be invalid. Please reboot the ELC again or re-connect ACPGMXFR to ELC.
ELC program will be invalid. Please reboot ELC again or re-connect the ACPGMXFR to ELC.
ACPGMXFR in “RD” mode:
ACPGMXFR in “WR” mode:
Error Message
Model
SP
10
20
⌧
⌧
0
21
11
⌧
⌧
1
!
12
22
⌧
⌧
2
"
1 min. 10 sec.
13
23
⌧
⌧
Synchronous blinking
3
#
Blinking
35 sec.
Read
ERR
On
On
Off
Cross blinking
Indicator
14
24
⌧
⌧
4
$
M1085=OFF
Blinking
15
25
⌧
⌧
%
5
OK
On
Off
Off
Appendix: ASCII Table
16
26
⌧
⌧
&
6
1 min. 15 sec.
Troubleshooting
Error Message
ACPGMXFR hardware may be damaged, please replace it.
Make sure ACPGMXFR model record is compatible with ELC
model.
Check ELC program syntax.
ACPGMXFR doesn’t contain any data and in “WR” mode.
ACPGMXFR in “WR” mode, and ELC is in RUN mode. Please
keep ELC in STOP mode.
Communication protocol error! Please confirm ELC in STOP mode
and reboot the ELC.
ELC protect with password.
Communication protocol error! Please confirm ELC in STOP mode
and reboot the ELC.
ACPGMXFR is in “RD” mode, and is protected by password.
Please push erase button when ACPGMXFR connect to ELC. For
more detail operation of erasure, please reference to section 3.4.
ACPGMXFR is in “WR” mode, and ELC is protected by password.
Please disable the password in ELC, or set the same ELC’s
password in ACPGMXFR. For more detail operation , please
reference to section 3.2.
Please refer to section 3.4.
45 sec.
Write
⌧
17
⌧
27
3
7
'
⌧
18
⌧
28
8
(
⌧
19
⌧
29
9
)
1 min. 5 sec.
30 sec.
Recommend
1A
2A
⌧
⌧
A
Read
*
1B
2B
⌧
⌧
B
+
M1085=ON
1C
2C
⌧
⌧
C
,
1 min. 10 sec.
1D
2D
⌧
⌧
D
IL05003020E.pdf
-
35 sec.
Write
1E
2E
⌧
⌧
E
.
1F
2F
⌧
⌧
F
/