MAX5054AATA-T Maxim Integrated Products, MAX5054AATA-T Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX5054AATA-T
Manufacturer Part Number
MAX5054AATA-T
Description
MOSFET & Power Driver ICs 4A 20ns Dual MOSFET Drivers
Manufacturer
Maxim Integrated Products
Type
Low Sider
Datasheet
1.MAX5054AATAT.pdf
(15 pages)
Specifications of MAX5054AATA-T
Rise Time
85 ns
Fall Time
75 ns
Supply Voltage (min)
4 V
Supply Current
2.4 mA
Maximum Power Dissipation
1454 mW
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Maximum Turn-off Delay Time
35 ns
Maximum Turn-on Delay Time
35 ns
Minimum Operating Temperature
- 40 C
Number Of Drivers
2
Number Of Outputs
2
Pay extra attention to bypassing and grounding the
MAX5054–MAX5057. Peak supply and output currents
may exceed 8A when both drivers drive large external
capacitive loads in phase. Supply voltage drops and
ground shifts create forms of negative feedback for
inverters and may degrade the delay and transition times.
Ground shifts due to insufficient device grounding may
also disturb other circuits sharing the same AC ground
return path. Any series inductance in the V
and/or GND paths can cause oscillations due to the very
high di/dt when switching the MAX5054–MAX5057 with
any capacitive load. Place one or more 0.1µF ceramic
capacitors in parallel as close to the device as possible to
bypass V
ground return resistance and series inductance. Place
the external MOSFET as close as possible to the
MAX5054–MAX5057 to further minimize board induc-
tance and AC path impedance.
Power dissipation of the MAX5054–MAX5057 consists
of three components: caused by the quiescent current,
capacitive charge/discharge of internal nodes, and the
output current (either capacitive or resistive load).
Maintain the sum of these components below the maxi-
mum power dissipation limit.
The current required to charge and discharge the internal
nodes is frequency dependent (see the Supply Current
vs. Supply Voltage graph in the Typical Operating
Characteristics ). The power dissipation (P
quiescent switching supply current (I
can be calculated as:
For capacitive loads, use the following equation to esti-
mate the power dissipation per driver:
where C
voltage, and f
Calculate the total power dissipation (P
follows:
Use the following equation to estimate the MAX5054–
MAX5057 total power dissipation per driver when driving
a ground-referenced resistive load:
LOAD
DD
P
P
RLOAD
CLOAD
Supply Bypassing and Grounding
to GND. Use a ground plane to minimize
SW
is the capacitive load, V
is the switching frequency.
P
______________________________________________________________________________________
P
P
Q
= D x R
T
T
= C
= P
= P
= V
LOAD
Q
Q
DD
+ P
+ P
ON(MAX)
x I
x (V
CLOAD
RLOAD
DD-SW
Power Dissipation
DD
x I
)
2
DD-SW
LOAD
x f
DD
T
4A, 20ns, Dual MOSFET Drivers
) per driver as
SW
Q
is the supply
) due to the
2
) per driver
DD
, OUT_,
where D (duty cycle) is the fraction of the period the
MAX5054–MAX5057’s output pulls high duty cycle,
R
with the output high, and I
of the MAX5054–MAX5057.
The MAX5054–MAX5057 MOSFET drivers source and
sink large currents to create very fast rising and falling
edges at the gate of the switching MOSFET. The high
di/dt can cause unacceptable ringing if the trace
lengths and impedances are not well controlled. Use the
following PC board layout guidelines when designing
with the MAX5054–MAX5057:
•
•
•
•
•
ON(MAX)
Place one or more 0.1µF decoupling ceramic
capacitors from V
as possible. Connect V
areas. Place one bulk capacitor of 10µF (min) on
the PC board with a low resistance path to the V
input and GND of the MAX5054–MAX5057.
Two AC current loops form between the device and
the gate of the driven MOSFET. The MOSFET looks
like a large capacitance from gate to source when the
gate pulls low. The active current loop is from the
MOSFET gate to OUT_ of the MAX5054–MAX5057, to
GND of the MAX5054–MAX5057, and to the source of
the MOSFET. When the gate of the MOSFET pulls
high, the active current is from the V
decoupling capacitor, to V
MAX5057, to OUT_ of the MAX5054–MAX5057, to the
MOSFET gate, to the MOSFET source, and to the
negative terminal of the decoupling capacitor. Both
charging current and discharging current loops are
important. Minimize the physical distance and the
impedance in these AC current paths.
Keep the device as close to the MOSFET as possible.
In a multilayer PC board, the inner layers should
consist of a GND plane containing the discharging
and charging current loops.
Pay extra attention to the ground loop and use a
low-impedance source when using a TTL logic-
input device. Fast fall time at OUT_ may corrupt the
input during transition.
is the maximum on-resistance of the device
DD
to GND as close to the device
LOAD
DD
and GND to large copper
Layout Information
is the output load current
DD
of the MAX5054–
DD
terminal of the
DD
11