0638508070 Molex Inc, 0638508070 Datasheet

no-image

0638508070

Manufacturer Part Number
0638508070
Description
TOOL KIT
Manufacturer
Molex Inc
Datasheets
1.0638508070.pdf (2 pages)
2.0638508070.pdf (6 pages)

Specifications of 0638508070

Lead Free Status / Rohs Status
RoHS Not Applicable
T2 Terminator “Micro-Fit 3.0™” Crimp Terminals
Doc No. 63850-8000
Revision: B
FEATURES
Œ
Œ
Œ
Œ
Œ
SCOPE
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.
It is ideally suited for mid-volume bench operations
This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press
Quick punch removal with the push of a button for fast and easy tooling change
Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab length
T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory requirements
BRUSH
LENGTH
STRIP
Release Date: 02-24-05
Revision Date: 02-24-05
43030-0004
43030-0005
43030-0006
43031-0004
43031-0005
43031-0006
Series No.
Terminal
AWG
26-30
26-30
26-30
26-30
26-30
26-30
CUT-OFF TAB
Wire Size
Part No. 63850-8000
T2 Terminator Tooling
0.12-0.05
0.12-0.05
0.12-0.05
0.12-0.05
0.12-0.05
0.12-0.05
Specification Sheet
INSULATION
mm²
CRIMP
1.12-1.27
1.12-1.27
1.12-1.27
1.12-1.27
1.12-1.27
1.12-1.27
UNCONTROLLED COPY
Insulation Diameter
CONDUCTOR
mm
BELL MOUTH
CRIMP
.044-.050
.044-.050
.044-.050
.044-.050
.044-.050
.044-.050
SEAM
In.
COND.CRIMP
HEIGHT
2.54-2.92
2.54-2.92
2.54-2.92
2.54-2.92
2.54-2.92
2.54-2.92
mm
Strip Length
BEND UP
DOWN
BEND
.100-.115
.100-.115
.100-.115
.100-.115
.100-.115
.100-.115
In.
TWISTING
ROLLING
Page 1 of 6

0638508070 Summary of contents

Page 1

T2 Terminator “Micro-Fit 3.0™” Crimp Terminals FEATURES Œ ideally suited for mid-volume bench operations Œ This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press Œ Quick punch removal ...

Page 2

T2 Terminator “Micro-Fit 3.0™” Crimp Terminals CRIMP SPECIFICATION Terminal Series No. 43030-0004 43030-0005 43030-0006 43031-0004 43031-0005 43031-0006 Bend up Bend down Terminal Series No. Degree 43030-0004 3 43030-0005 3 43030-0006 3 43031-0004 3 43031-0005 3 43031-0006 3 After crimping, the ...

Page 3

T2 Terminator for “Micro-Fit 3.0™” Crimp Terminals PARTS LIST Item Order No 63850-8000 1 63444-1116 2 63445-1122 3 63446-1610 4 63445-1613 5 63443-0002 6 63443-0012 7 11-24-1067 8 11-40-4039 9 63443-0021 10 63443-6003 11 11-18-4083 12 63443-2409 13 63443-4005 14 ...

Page 4

T2 Terminator for “Micro-Fit 3.0™” Crimp Terminals Assembly Drawing Doc No. 63850-8000 Release Date: 02-25-05 Revision: B Revision Date: 02-25- Figure 1 UNCONTROLLED COPY ...

Page 5

T2 Terminator for “Micro-Fit 3.0™” Crimp Terminals NOTES Depending on the press vintage a feed finger assembly is supplied with the T2 Terminator remove the existing feed finger assembly loosens the set screw in ...

Page 6

T2 Terminator for “Micro-Fit 3.0™” Crimp Terminals NOTES 1. Molex recommends an extra perishable tooling kit be maintained at your facility. 2. Verify tooling alignment by manually cycling the press before crimping under power. Check that all screws are tight. ...