MAX17116EVKIT# Maxim Integrated Products, MAX17116EVKIT# Datasheet - Page 2

• Manufacturer Part Number: MAX17116EVKIT#
• Description: Power Management Modules & Development Tools MAX17116 Eval Kit
• Manufacturer: Maxim Integrated Products

Specifications of MAX17116EVKIT#

• Lead Free Status / Rohs Status: Details

• MAX17116 EV kit
• +2.3V to +4.2V, 1A power supply (VIN)
• Two digital voltmeters
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn on
the power supply until all connections are completed.
1) Verify that jumper JU1 is in the default position, as
2) Connect the positive terminal of the power supply
3) Connect the first voltmeter across the ELVDD PCB
4) Connect the second voltmeter across the ELVSS PCB
5) Turn on the DC power supply.
6) Verify that the voltmeters display V
The MAX17116 EV kit includes two current-mode
1.4MHz SMPS regulators for AMOLED displays. The
positive supply is provided by a step-up regulator with a
synchronous rectifier. The negative supply is provided
Table 1. Jumper JU1 Function
*Default position.
Evaluates: MAX17116 in a 12-Pin UTDFN Package
Detailed Description of Hardware
shown in Table 1.
to the VIN PCB pad and the negative terminal to the
nearest PGND PCB pad.
pad and the nearest PGND PCB pad.
pad and the nearest PGND PCB pad.
V
ELVSS
SHUNT POSITION
Not installed
= -4.9V.
1-2*
2-3
_________________________________________________________________ Maxim Integrated Products 2
Recommended Equipment
External pulses must be applied to the
ELVDD
Quick Start
Connected to AGND
Procedure
Connected to IN
= +4.6V and
EN test pad
EN PIN
by an inverting regulator with a synchronous rectifier.
The step-up regulator output is a fixed voltage of +4.6V
and the inverting regulator output is adjustable from -5.4V
to -1.5V through the single-wire EN serial interface. The EV
kit operates from a +2.3V to +4.2V single power supply.
The EV kit includes a step-up DC-DC converter with an
integrated power MOSFET switch and synchronous
rectifier. The step-up regulator output (ELVDD) has a
fixed voltage of +4.6V and can provide an output current
of 250mA.
The EV kit contains an inverting DC-DC converter with
integrated power MOSFET switch and synchronous recti-
fier. The inverting regulator output (ELVSS) is adjustable
from -5.4V to -1.5V and can provide an output current
of 250mA. The ELVSS output voltage can be adjusted
through the single-wire EN serial interface.
The EV kit features a 3-pin jumper (JU1) to control the
enable input and an EN test pad to access the serial inter-
face input. Connect EN to IN for normal operation. Connect
EN to AGND to place the device into shutdown mode.
The enable pin is also used as a serial-interface input
to adjust the inverting converter output voltage. With no
shunts installed on jumper JU1, connect an external pulse
generator at the EN test pad and send the required serial
pulses. Refer to the EN Serial Interface section in the
MAX17116 IC data sheet for a more detailed description.
Table 1 lists the selectable jumper options.
Enable Input and Serial Interface Input
V
ELVSS
= -5.4V to -1.5V (based on EN pulses)
SMPS REGULATORS
V
V
V
ELVDD
ELVDD
V
ELVSS
V
ELVDD
ELVSS
Inverting Converter
Step-Up Regulator
= +4.6V
= +4.6V
= -4.9V
= 0V
= 0V