DS21348T+ Maxim Integrated Products, DS21348T+ Datasheet - Page 14
![IC LIU T1/E1/J1 3.3V 44-TQFP](/photos/6/86/68678/406-44-tqfp_sml.jpg)
DS21348T+
Manufacturer Part Number
DS21348T+
Description
IC LIU T1/E1/J1 3.3V 44-TQFP
Manufacturer
Maxim Integrated Products
Type
Line Interface Units (LIUs)r
Datasheet
1.DS21348G.pdf
(76 pages)
Specifications of DS21348T+
Number Of Drivers/receivers
1/1
Protocol
T1/E1/J1
Voltage - Supply
3.135 V ~ 3.465 V
Mounting Type
Surface Mount
Package / Case
44-TQFP, 44-VQFP
Product
Framer
Number Of Transceivers
1
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Supply Current (max)
100 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
2.1 Pin Descriptions
Table 2-5. Pin Descriptions in Parallel Port Mode (Sorted by Pin Name,
DS21348T Pin Numbering)
D0/AD0 to
BIS0/BIS1
ALE (AS)
A0 to A4
D7/AD7
BPCLK
NAME
MCLK
HRST
PBEO
N/A
INT
CS
19 to 12
11 to 7
32/33
PIN
31
29
23
30
—
24
4
1
I/O
I/O
O
O
O
I
I
I
I
I
I
I
Address Bus. In nonmultiplexed bus operation (BIS1 = 0, BIS0 =
1), serves as the address bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), these pins are not used and should be tied low.
Address Latch Enable (Address Strobe). When using the parallel
port (BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to
demultiplex the bus on a positive-going edge. In nonmultiplexed bus
mode (BIS0 = 1), should be tied low.
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. See
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
Chip Select, Active Low. This active-low signal must be low to
read or write to the device.
Data Bus/Address/Data Bus. In nonmultiplexed bus operation
(BIS1 = 0, BIS0 = 1), serves as the data bus. In multiplexed bus
operation (BIS1 = 0, BIS0 = 0), serves as an 8-bit multiplexed
address/data bus.
Hardware Reset, Active Low. Bringing HRST low resets the
DS21348, setting all control bits to their default state of all zeros.
Interrupt, Active Low. Flags host controller during conditions and
change of conditions defined in the Status Register. Active low,
open drain output.
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional.
Not Assigned. Should be tied low.
PRBS Bit Error Output. The receiver will constantly search for a
2
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
15
-1 or a 2
20
Table 2-1
14 of 76
-1 PRBS depending on the ETS bit setting (CCR1.7).
for details.
FUNCTION