LMX25311778EVAL National Semiconductor, LMX25311778EVAL Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LMX25311778EVAL
Manufacturer Part Number
LMX25311778EVAL
Description
Manufacturer
National Semiconductor
Datasheet
1.LMX25311778EVAL.pdf
(34 pages)
Specifications of LMX25311778EVAL
Lead Free Status / Rohs Status
Not Compliant
2.0 General Programming Information
The LMX2531 is programmed using 11 24-bit registers used to control the LMX2531 operation. A 24-bit shift register is used as a
temporary register to indirectly program the on-chip registers. The shift register consists of a data field and an address field. The
last 4 register bits, CTRL[3:0] form the address field, which is used to decode the internal register address. The remaining 20 bits
form the data field DATA[19:0]. While LE is low, serial data is clocked into the shift register upon the rising edge of clock (data is
programmed MSB first). When LE goes high, data is transferred from the data field into the selected register bank. Although there
are actually 14 registers in this part, only a portion of them should be programmed, since the state of the other hidden registers
(R13, R11, and R10) are set during the initialization sequence. Although it is possible to program these hidden registers, as well
as a lot of bits that are defined to either '1' or '0', the user should not experiment with these hidden registers and bits, since the
parts are not tested under these conditions and doing so will most likely degrade performance.
2.01 Register Location Truth Table
2.02 Initialization Sequence
The initial loading sequence from a cold start is described below. The registers must be programmed in order shown. There must
be a minimum of 10 ms between the time when R5 is last loaded and R1 is loaded to ensure time for the LDOs to power up properly.
MSB
D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 C3 C2 C1
REG.
INIT1
INIT2
R12
R5
R5
R5
R9
R8
R7
R6
R4
R3
R2
R1
R0
C3
1
1
1
0
0
0
0
0
0
0
0
23 22 21 20 19 18 17 16 15 14 13 12 11 10
1
1
1
0
0
0
0
0
0
Programming of this register is necessary under specific circumstances.
0
0
0
See individual section for Register R8 programming information.
See individual section for Register R7 programming information.
See individual section for Register R6 programming information.
See individual section for Register R4 programming information.
See individual section for Register R3 programming information.
See individual section for Register R2 programming information.
See individual section for Register R1 programming information.
See individual section for Register R0 programming information.
Register R4 only needs to be programmed if FastLock is used.
0
0
0
Program R12 as shown in the complete register map.
Program R9 as shown in the complete register map.
C2
1
0
0
1
1
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
DATA[19:0]
0
0
0
DATA[19:0]
0
0
0
0
0
0
C1
19
0
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
1
9
0
0
1
8
0
0
1
C0
0
1
0
1
0
1
0
1
0
1
0
7
0
0
1
6
0
0
1
5
0
0
1
4
0
0
1
Data Address
C3 C2 C1 C0
CONTROL[3:0]
3
0
0
0
1
1
1
0
0
0
0
0
0
0
R12
R9
R8
R7
R6
R5
R4
R3
R2
R1
R0
2
1
1
1
1
0
0
1
1
1
0
0
0
0
www.national.com
1
0
0
0
0
0
0
1
1
0
1
1
0
0
LSB
C0
0
1
1
1
0
1
0
1
0
0
1
0
1
0