DS3650M National Semiconductor, DS3650M Datasheet - Page 2

• Manufacturer Part Number: DS3650M
• Description: IC LINE RCVR QUAD DIFF 16-SOIC
• Manufacturer: National Semiconductor
• Type: Line Receiverr

Specifications of DS3650M

• Number Of Drivers/receivers: 0/4
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Package / Case: *
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Protocol: -
• Other names: *DS3650M

www.national.com
Symbol
V
I
I
I
V
V
I
I
I
I
IH(I)
IL(I)
IL(S)
OS
OFF
CCH
EEH
Electrical Characteristics
(V
I
Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. Except for “Operating Temperature Range” they
are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Note 3: Unless otherwise specified, min/max limits apply across the 0˚C to +70˚C range for the DS3650. All typical values are for T
−5V.
Note 4: All currents into device pins shown as positive, out of device pins as negative, all voltages referenced to ground unless otherwise noted. All values shown
as max or min on absolute value basis.
Note 5: Only one output at a time should be shorted.
Note 6: A parameter which is of primary concern when designing with line receivers is, what is the minimum differential input voltage required as the receiver input
terminals to guarantee a given output logic state. This parameter is commonly referred to as threshold voltage. It is well known that design considerations of threshold
voltage are plagued by input offset currents, bias currents, network source resistances, and voltage gain. As a design convenience, the DS3650 is specified to a pa-
rameter called input sensitivity (V
age to cause a given output logic state with respect to a maximum source impedance of 200
IS
OH
OL
Absolute Maximum Ratings
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Power Supply Voltages
Differential-Mode Input Signal Voltage
Common-Mode Input Voltage Range,
Strobe Input Voltage, V
Storage Temperature Range
Lead Temperature
Maximum Power Dissipation (Note 1)
IH(S)
CC
V
V
Range, V
V
(Soldering, 4 seconds)
at 25˚C
Cavity Package
Molded DIP Package
CC
EE
ICR
= 5.0 V
Input Sensitivity, (Note 6)
High Level Input Current to
Receiver Input
Low Level Input Current to
Receiver Input
High Level Input Current to Strobe Input
Low Level Input Current to Strobe Input
High Level Output Voltage
Low Level Output Voltage
Short-Circuit Output Current (Note 5)
Output Disable Leakage Current
High Logic Level Supply Current
from V
High Logic Level Supply Current
from V
IDR
(Common-Mode Voltage Range =
−3V
DC
, V
CC
EE
EE
V
IN
= −5.0 V
I(S)
3V)
Parameter
IS
). This parameter takes into consideration input offset currents and bias currents and guarantees a minimum input differential volt-
DC
, Min
T
A
(Notes 3, 4)
−65˚C to +150˚C
Max, unless otherwise noted)
(Note 2)
1509 mW
1476 mW
±
±
+7.0 V
−7.0 V
6.0 V
5.0 V
5.5 V
260˚C
Min
Min
( Figure 5 )
( Figure 6 )
( Figure 3 )
( Figure 1 )
( Figure 1 )
( Figure 4 )
( Figure 7 )
( Figure 2 )
( Figure 2 )
DC
DC
DC
DC
DC
V
V
CC
EE
2
Operating Conditions
Supply Voltage, V
Supply Voltage, V
Operating Temperature, T
Output Load Current, I
Differential-Mode Input
Common-Mode Input
Input Voltage Range
Note 1: Derate cavity package 10.1 mW/˚C above 25˚C; derate molded DIP
package 11.8 mW/˚C above 25˚C; derate SO package 8.41 mW/˚C above
25˚C.
Conditions
Max
Max
SO Package
Voltage Range, V
Voltage Range, V
Input to GND, V
at each input.
V
V
V
IH(S)
IH(S)
IH(S)
= 2.4V
= V
= 0.4V
CC
EE
IR
CC
IDR
ICR
OL
A
Min
−18
2.4
−4.75
4.75
−5.0
−3.0
−5.0
Min
A
0
= 25˚C, V
Typ
−17
45
CC
−5.25
±
Max
5.25
+5.0
+3.0
+3.0
+70
Max
−1.6
0.45
−10
−70
−30
16
25.0
40
75
40
60
= 5V and V
1
1051 mW
Units
Units
EE
V
V
V
V
V
mV
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
˚C
V
V
DC
DC
DC
DC
DC
=