DS2480B Maxim Integrated Products, DS2480B Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS2480B
Manufacturer Part Number
DS2480B
Description
IC LINE DRVR W/SENSOR 1-W 8-SOIC
Manufacturer
Maxim Integrated Products
Type
Line Driver, Transmitterr
Datasheet
1.DS2480B.pdf
(31 pages)
Specifications of DS2480B
Number Of Drivers/receivers
1/0
Protocol
RS232
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS2480B
Manufacturer:
DALLAS
Quantity:
5 510
Part Number:
DS2480B
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS2480B+
Manufacturer:
Maxim
Quantity:
2 862
Part Number:
DS2480B+
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS2480B+TR
Manufacturer:
MAXIM/美信
Quantity:
20 000
Figure 11d. UART DIRECT OPTO-ISOLATED
The circuit in Figure 11d is essentially the same as in Figure 11a. The main difference is the opto-
isolation. The characteristics of the opto-isolators are not very critical. Using a different type will affect
the values of the resistors that limit the current through the LEDs and bias the photo transistors.
Figure 11e. ±5 TO 12V RS232 OPTO-ISOLATED
The circuit in Figure 11e combines the true RS232C interface with opto-isolation. The energy to power
the LED in the TXD channel and to provide the positive voltage for the host’s RXD input is stolen from
DTR and RTS. The negative voltage for the RXD input is taken from the TXD line through a parasitic
supply consisting of a Schottky diode in series with a capacitor. The HCPL-2202 opto-isolator has a
totem pole output that allows switching in positive as well as negative voltage. The +5V are sufficient for
most RS232C systems. Switching in 12V requires an opto-isolator with different voltage characteristics.
In the schematic the HCPL-2202 opto-isolator is sourced by the RXD pin of the DS2480B. It can as well
be connected the traditional way where the DS2480B sinks the current through the LED. This, however,
causes a signal inversion that has to be compensated through the DS2480B by using a value code of 100,
101, 110, or 111 for the RS232 baud rate setting. Using other types of opto-isolators than shown in the
schematic will at least require changing the values of the resistors.
or µC
UART
or µC
UART
Start
L
Power Stealing
RTS
SIN
(RXD)
DTR
SOUT
(TXD)
1 µf
SIN
(RXD)
SOUT
(TXD)
5 V
Start
1
0
L
2.7K
M
Stop
1
0
Regulator
1.5K
HCPL-2300
5V
5.1K
M
Stop
* only one DS950x ESD protection device with 5V
* only one DS950x ESD protection device with 5V
DC to DC
Converter
HCPL-2300
HCPL-2202
DC/DC
Convert.
27 of 31
5.1K
1.5K
2.7K
5V
2.7K
12 V
VDD
RXD
TXD
DS2480
GND
VPP
VPP
TXD
RXD
DS2480
POL
1-W
+12VDC Programming
GND
VDD
POL
1-W
Return
1-Wire Bus
Return
1-Wire Bus
5V
DS9503
DS9503
DS9503
*
DS9503
*