MAXQ2000-QAX Maxim Integrated Products, MAXQ2000-QAX Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAXQ2000-QAX
Manufacturer Part Number
MAXQ2000-QAX
Description
Microcontrollers (MCU) Low-Power LCD MCU
Manufacturer
Maxim Integrated Products
Datasheet
1.MAXQ2000-RAX.pdf
(38 pages)
Specifications of MAXQ2000-QAX
Processor Series
MAXQ2000
Core
RISC
Data Bus Width
16 bit
Program Memory Type
Flash
Program Memory Size
64 KB
Data Ram Size
2 KB
Interface Type
1-Wire, SPI, JTAG, UART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
50
Number Of Timers
3
Operating Supply Voltage
1.8 V to 2.75 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
QFN-68
Development Tools By Supplier
MAXQ2000-KIT
Minimum Operating Temperature
- 40 C
Low-Power LCD Microcontroller
The watchdog timer is controlled through bits in the
WDCN register. Its timeout period can be set to one of
four programmable intervals ranging from 2
system clocks in its default mode, allowing flexibility to
support different types of applications. The interrupt
occurs 512 system clocks before the reset, allowing the
system to execute an interrupt and place the system in
a known, safe state before the device performs a total
system reset. At 16MHz, watchdog timeout periods can
be programmed from 256µs to 33.5s, depending on the
system clock mode.
The microcontroller incorporates several common seri-
al-peripheral interfaces for interconnection with popular
external devices. Multiple formats provide maximum
flexibility and lower cost when designing a system.
Serial interfacing is provided through one (-RBX/-RBX+)
or two (-RAX/-RAX+/-RFX/-RFX+) 8051-style universal
synchronous/asynchronous receiver/transmitters. The
UART allows the device to conveniently communicate
with other RS-232 interface-enabled devices, as well as
PCs and serial modems when paired with an external
RS-232 line driver/receiver. The dual independent
UARTs can communicate simultaneously at different
baud rates with two separate peripherals. The UART
can detect framing errors and indicate the condition
through a user-accessible software bit.
The time base of the serial ports is derived from either a
division of the system clock or the dedicated baud
clock generator. The following table summarizes the
operating characteristics as well as the maximum baud
rate of each mode:
iButton is a registered trademark of Dallas Semiconductor Corp., a wholly owned subsidiary of Maxim Integrated Products, Inc.
30
____________________________________________________________________
Mode 0
Mode 1
Mode 2
Mode 3
MODE
Asynchronous
Asynchronous
Asynchronous
Synchronous
Serial Peripherals
TYPE
START BITS
12
N/A
UARTs
1
1
1
to 2
21
The MAXQ2000-RAX/-RAX+/-RFX/-RFX+ include a
Dallas Semiconductor 1-Wire bus master, which commu-
nicates to other 1-Wire peripherals, including iButton
products, through a simple bidirectional signaling
scheme over a single electrical connection. The bus
master provides complete control of the 1-Wire bus and
transmit and receive activities, and generates all timing
and control sequences of the 1-Wire bus.
Communication between the CPU and the bus master
is achieved through read/write access of the 1-Wire
master address (OWA) and 1-Wire master data (OWD)
peripheral registers. Detailed operation of the 1-Wire
bus is described in the Book of iButton Standards
(www.maxim-ic.com/iButtonbook).
The SPI port is a common, high-speed, synchronous
peripheral interface that shifts a bit stream of variable
length and data rate between the microcontroller and
other peripheral devices. The SPI can be used to com-
municate with other microcontrollers, serial shift regis-
ters, or display drivers. Multiple master and slave
modes permit communication with multiple devices in
the same system. Programmable clock frequency,
character lengths, polarity, and error handling enhance
the usefulness of the peripheral. The maximum baud
rate of the SPI interface is 1/2 the system clock for mas-
ter mode operation and 1/8 the system clock for slave
mode operation.
DATA BITS
Serial-Peripheral Interface (SPI) Module
8 + 1
8 + 1
8
8
STOP BIT
N/A
1
1
1
1-Wire Bus Master
MAX BAUD RATE
AT 16MHz
500kbps
500kbps
500kbps
4Mbps
®