LTC1164ACSW#PBF Linear Technology, LTC1164ACSW#PBF Datasheet
LTC1164ACSW#PBF
Specifications of LTC1164ACSW#PBF
Related parts for LTC1164ACSW#PBF
LTC1164ACSW#PBF Summary of contents
Page 1
... Antialiasing Filters Telecom Filters Spectral Analysis Loop Filters For Fixed Lowpass Filter Requirements use the LTC1164-XX Series , LTC and LT are registered trademarks of Linear Technology Corporation. LTCMOS trademark of Linear Technology Corporation. U TYPICAL APPLICATIO Dual 5th Order Linear Phase Filter with Stopband Notch 549k ...
Page 2
LTC1164 ABSOLUTE AXI U RATI GS + – Total Supply Voltage ( ............................ 16.5V Power Dissipation .............................................. 500mW Storage Temperature Range ..................–65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C U PACKAGE/ORDER I FOR ...
Page 3
ELECTRICAL CHARACTERISTICS range,otherwise specifications are PARAMETER Center Frequency Range Input Frequency Range (Note 2) Clock-to-Center Frequency Ratio CLK O LTC1164A LTC1164 LTC1164A LTC1164 Clock-to-Center Frequency Ratio, Side to Side Matching LTC1164A LTC1164 Q Accuracy f ...
Page 4
LTC1164 ELECTRICAL CHARACTERISTICS V OS1 (12, 13, 24) + – Figure 1. Equivalent Input Offsets of 1/4 LTC1164 Filter Building Block Table 1. Output DC Offsets One 2nd Order Section V MODE PIN 2, 11, 14 ...
Page 5
W BLOCK DIAGRA – INV A(12) + AGND(6) – INV B(1) + – INV C(24) + – INV D(13) + HPA/NA(11) BPA(10) LPA( – HPB/NB(2) BPB(3) LPB(4) SA( – HPC/NC(23) BPC(22) LPC(21) SB(5) + ...
Page 6
LTC1164 W U TYPICAL PERFOR A CE CHARACTERISTICS Mode 50:1 CLK 25° ±2. ±7. ...
Page 7
CTIO S Power Supplies (Pins 7,19) They should be bypassed with 0.1µF ceramic disc. Low noise, non-switching, power supplies are recommended. The device operates with a single 5V supply and with dual supplies. The absolute ...
Page 8
LTC1164 U U APPLICATIO S I FOR ATIO ANALOG CONSIDERATIONS 1. Grounding and Bypassing The LTC1164 should be used with separated analog and digital ground planes and single point grounding techniques. Pin 6 (AGND) should be tied directly to the ...
Page 9
U U APPLICATIO S I FOR ATIO 3. Offset Nulling Lowpass filters may have too much DC offset for some users. A servo circuit may be used to actively null the offsets of the LTC1164 or any LTC switched capacitor ...
Page 10
LTC1164 W ODES OF OPERATIO Mode 3 Mode 3 is the second of the primary modes. In Mode 3, the ratio of the external clock frequency to the center frequency of each 2nd order section can be adjusted above or ...
Page 11
W ODES OF OPERATIO Mode 3A This is an extension of Mode 3 where the highpass and lowpass output are summed through two external resis- tors R and R to create a notch. This is shown in Figure H L ...
Page 12
LTC1164 U TYPICAL APPLICATIO S 196k Figure 11. 8th Order Lowpass Butterworth, Passband Noise 90µV (Also Refer to the LTC1164-5) LTC1164 8th Order Butterworth 500kHz 10kHz CLK –3dB 10.00 0.0 –10.00 –20.00 –30.00 ...
Page 13
U TYPICAL APPLICATIO S 63. 2.5V LT1004 Figure 12. 8th Order Lowpass Single Supply Elliptic-Bessel Transitional Filter Total Supply Current = 4mA, Passband Noise 50µV LTC1164 8th Order Lowpass, Elliptic-Bessel Traditional Filter Single 5V Supply 10.00 0.0 –10.00 ...
Page 14
LTC1164 U TYPICAL APPLICATIO 0.1µ Figure 13. LTC1164 8th Order Lowpass Elliptic, f Passband Noise = 110µ ...
Page 15
... OR TIN PLATE LEADS Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ALL RESISTORS MF 1% ...
Page 16
... N24 1002 .598 – .614 (15.190 – 15.600) NOTE .394 – .419 (10.007 – 10.643) N .037 – .045 (0.940 – 1.143) .004 – .012 (0.102 – 0.305) S24 (WIDE) 0502 LT/TP 1202 1K REV A • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1991 1164fa ...