MCP23008-E/SO Microchip Technology, MCP23008-E/SO Datasheet - Page 19
![IC I/O EXPANDER I2C 8B 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
MCP23008-E/SO
Manufacturer Part Number
MCP23008-E/SO
Description
IC I/O EXPANDER I2C 8B 18SOIC
Manufacturer
Microchip Technology
Specifications of MCP23008-E/SO
Package / Case
18-SOIC (7.5mm Width)
Interface
I²C
Number Of I /o
8
Interrupt Output
Yes
Frequency - Clock
1.7MHz
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Includes
POR
Logic Family
MCP23008
Propagation Delay Time
50 ns
Operating Supply Voltage
1.8 V to 5.5 V
Power Dissipation
700 mW
Operating Temperature Range
- 40 C to + 125 C
Input Voltage
1.8 V to 5.5 V
Logic Type
I/O Expander
Maximum Clock Frequency
10 MHz
Maximum Operating Frequency
1.7 MHz
Mounting Style
SMD/SMT
Output Current
25 mA
Output Voltage
1.8 V to 4.5 V
Chip Configuration
8 Bit
Bus Frequency
1.7MHz
Ic Interface Type
I2C, Serial
No. Of I/o's
8
Supply Voltage Range
1.8V To 5.5V
Digital Ic Case Style
SOIC
No. Of Pins
18
Delay Time
50ns
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
GPIODM-KPLCD - BOARD DEMO LCD GPIO EXP KEYPAD
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP23008-E/SO
Manufacturer:
MICROCHIP
Quantity:
8 700
Part Number:
MCP23008-E/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
1.7
The interrupt output pin will activate if an internal
interrupt occurs. The interrupt block is configured by
the following registers:
• GPINTEN – enables the individual inputs
• DEFVAL – holds the values that are compared
• INTCON – controls if the input values are
• IOCON (ODR and INPOL) – configures the INT
Only pins configured as inputs can cause interrupts.
Pins configured as outputs have no affect on INT.
Interrupt activity on the port will cause the port value to
be captured and copied into INTCAP. The interrupt will
remain active until the INTCAP or GPIO register is
read. Writing to these registers will not affect the
interrupt.
The first interrupt event will cause the port contents to
be copied into the INTCAP register. Subsequent
interrupt conditions on the port will not cause an
interrupt to occur as long as the interrupt is not cleared
by a read of INTCAP or GPIO.
1.7.1
There are two possible configurations to cause
interrupts (configured via INTCON):
1.
2.
See Figure 1-6 and Figure 1-7 for more information on
interrupt operations.
© 2005 Microchip Technology Inc.
against the associated input port values
compared against DEFVAL or the previous values
on the port
pin as push-pull, open-drain and active-level
Pins configured for interrupt-on-pin-change
will cause an interrupt to occur if a pin changes
to the opposite state. The default state is reset
after an interrupt occurs. For example, an
interrupt occurs by an input changing from 1 to
0. The new initial state for the pin is a logic 0.
Pins configured for interrupt-on-change from
register value will cause an interrupt to occur if
the corresponding input pin differs from the
register bit. The interrupt condition will remain as
long as the condition exists, regardless if the
INTAP or GPIO is read.
Interrupt Logic
INTERRUPT CONDITIONS
MCP23008/MCP23S08
FIGURE 1-6:
FIGURE 1-7:
GP:
GP2
INT
Port value
is captured
into INTCAP
GPx
INT
Port value
is captured
into INTCAP
7
X
6
X
ACTIVE
ACTIVE
5
X
INTERRUPT-ON-PIN-
CHANGE
Read GPIU
or INTCAP
INTERRUPT-ON-CHANGE
FROM REGISTER
DEFAULT
DEFVAL
4
X
(INT clears only if interrupt
condition does not exist.)
3
X
Read GPIU
or INTCAP
ACTIVE
2
0
DS21919B-page 19
Port value
is captured
into INTCAP
ACTIVE
1
X
0
X