MCP23S08-E/P Microchip Technology, MCP23S08-E/P Datasheet - Page 15
![IC I/O EXPANDER SPI 8B 18DIP](/photos/6/76/67657/18-dip_300mil__sml.jpg)
MCP23S08-E/P
Manufacturer Part Number
MCP23S08-E/P
Description
IC I/O EXPANDER SPI 8B 18DIP
Manufacturer
Microchip Technology
Specifications of MCP23S08-E/P
Package / Case
18-DIP (0.300", 7.62mm)
Interface
SPI
Number Of I /o
8
Interrupt Output
Yes
Frequency - Clock
10MHz
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Includes
POR
Logic Family
MCP23S08
Propagation Delay Time
50 ns
Operating Supply Voltage
1.8 V to 5.5 V
Power Dissipation
700 mW
Operating Temperature Range
- 40 C to + 125 C
Input Voltage
1.8 V to 5.5 V
Logic Type
I/O Expander
Maximum Clock Frequency
10 MHz
Maximum Operating Frequency
1.7 MHz
Mounting Style
Through Hole
Output Current
25 mA
Output Voltage
1.8 V to 4.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
GPIODM-KPLCD - BOARD DEMO LCD GPIO EXP KEYPAD
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
1.6.6
The IOCON register contains several bits for
configuring the device:
• The Sequential Operation (SEQOP) controls the
• The Slew Rate (DISSLW) bit controls the slew
REGISTER 1-6:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
incrementing function of the address pointer. If the
address pointer is disabled, the address pointer
does not automatically increment after each byte
is clocked during a serial transfer. This feature is
useful when it is desired to continuously poll
(read) or modify (write) a register.
rate function on the SDA pin. If enabled, the SDA
slew rate will be controlled when driving from a
high to a low.
U-0
—
CONFIGURATION (IOCON)
REGISTER
Unimplemented: Read as ‘0’.
SEQOP: Sequential Operation mode bit.
1 = Sequential operation disabled, address pointer does not increment.
0 = Sequential operation enabled, address pointer increments.
DISSLW: Slew Rate control bit for SDA output.
1 = Slew rate disabled.
0 = Slew rate enabled.
HAEN: Hardware Address Enable bit (MCP23S08 only).
Address pins are always enabled on MCP23008.
1 = Enables the MCP23S08 address pins.
0 = Disables the MCP23S08 address pins.
ODR: This bit configures the INT pin as an open-drain output.
1 = Open-drain output (overrides the INTPOL bit).
0 = Active driver output (INTPOL bit sets the polarity).
INTPOL: This bit sets the polarity of the INT output pin.
1 = Active-high.
0 = Active-low.
Unimplemented: Read as ‘0’.
U-0
—
IOCON – I/O EXPANDER CONFIGURATION REGISTER (ADDR 0x05)
W = Writable bit
‘1’ = Bit is set
SEQOP
R/W-0
DISSLW
R/W-0
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
MCP23008/MCP23S08
R/W-0
HAEN
• The Hardware Address Enable (HAEN) control bit
• The Open-Drain (ODR) control bit enables/
• The Interrupt Polarity (INTPOL) control bit sets
enables/disables the hardware address pins (A1,
A0) on the MCP23S08. This bit is not used on the
MCP23008. The address pins are always enabled
on the MCP23008.
disables the INT pin for open-drain configuration.
the polarity of the INT pin. This bit is functional
only when the ODR bit is cleared, configuring the
INT pin as active push-pull.
R/W-0
ODR
x = Bit is unknown
INTPOL
R/W-0
DS21919E-page 15
U-0
—
bit 0