85-16 3M Interconnect Solutions, 85-16 Datasheet

no-image

85-16

Manufacturer Part Number
85-16
Description
Manufacturer
3M Interconnect Solutions
Datasheet
1.85-16.pdf (4 pages)

Specifications of 85-16

Lead Free Status / Rohs Status
Supplier Unconfirmed
Scotchcast
Splice Kits 85 Series
Instructions
1.0 Applications
Designed for insulating and sealing cables rated up to a maximum of 1000 volts. These kits will accommodate
the following connectors and conductor sizes:
* Assuming wye or 4-way connection using same cable sizes. For other informations and configurations, see back of instruction sheet.
2.0 Kit Contents
Kit No.
85-10
85-12
85-14
85-16
� CAUTION
Working around energized electrical systems may cause serious injury
or death. Installation should be performed by personnel familiar with
good safety practice in handling electrical equipment. De-energize and
ground all electrical systems before installing product.
Mold Body................................................ A
Sealing Mastic
3M
Adhesive Film Strip.................................. D
(attached to mold body) ........................... B
™
H & C Tap Compression
H & C Tap Compression
H & C Tap Compression
Scotchcast
Inline Compression
Connector Type
Compression
H & C Tap
Split Bolt
Split Bolt
Split Bolt
Split Bolt
™
Resin 4......................... C
™
2/0 Stranded AWG (Tap)
4/0 Stranded AWG (Tap)
Multi-Mold Power Cable
2/0 Stranded AWG
2/0 Stranded AWG
4/0 Stranded AWG
#8 Stranded AWG
#4 Stranded AWG
#1 Stranded AWG
250 kcmil (Run)
500 kcmil (Run)
Conductor Size*
Maximum
750 kcmil
Max. Connector Size
(height plus width)
B
1 3/4"
1 3/4"
2 3/4"
2 3/4"
3 1/4"
3 3/4"
N/A
B
6"
A
Max. Sheath
Opening
D
3 1/2"
3 1/2"
6 1/2"
9"
Run &Tap – 7/16"
Run & Tap – 7/8"
Run &Tap – 3/4"
Run &Tap – 7/8"
Max. Cable O.D.*
Inline – 1 1/2"
C
Wye or 4-Way

85-16 Summary of contents

Page 1

... H & C Tap Compression 85-12 Split Bolt H & C Tap Compression 85-14 Split Bolt H & C Tap Compression 85-16 Inline Compression Split Bolt H & C Tap Compression * Assuming wye or 4-way connection using same cable sizes. For other informations and configurations, see back of instruction sheet. 2.0 Kit Contents Mold Body ...

Page 2

... Cable Connection for Horizontal Run 3.1 Prepare Cable. Scrape each cable exterior clean for a distance of 5" (8" for 85-16) from connector. If cable is sheathed, pencil insulation 3/4". 3.2 Make Connection. Make connection according to connector manufacturer's instructions. Crimped connector length should not be more than dimension "A". ...

Page 3

Level Splice. Ensure that top of mold is level. If support is needed, support the cable outside of the splice area. 3.9 Pour Splice. Mix resin per instructions on resin package. Pour into mold. 3.10 Seal Top of Mold. ...

Page 4

Remove liner from adhesive film strip supplied with kit. 4.6 Seal the open side of mold. Bring the mold's edges together, fold over and compress the adhesive film strip. Be sure the seal is complete. 4.7 Mix the resin ...