AT42QT1040-MMH Atmel, AT42QT1040-MMH Datasheet - Page 6

• Manufacturer Part Number: AT42QT1040-MMH
• Description: IC TOUCH SENSOR 4KEY 20-VQFN
• Manufacturer: Atmel
• Series: QTouch™r
• Type: Resistiver

Specifications of AT42QT1040-MMH

• Touch Panel Interface: 4, 2-Wire
• Number Of Inputs/keys: 4 Key
• Data Interface: I²C, Serial
• Data Rate/sampling Rate (sps, Bps): 200k
• Voltage Reference: Internal
• Voltage - Supply: 1.8 V ~ 5.5 V
• Current - Supply: 10mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-VQFN Exposed Pad, 20-HVQFN, 20-SQFN, 20-DHVQFN
• Output Type: Logic
• Input Type: Logic
• Supply Voltage: 1.8 V to 5.5 V
• Dimensions: 3 mm L x 3 mm W x 0.8 mm H
• Output Voltage: 0.7 V to 0.8 V
• Temperature Range: - 40 C to + 85 C
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: AT42QT1040-MMH; AT42QT1040-MMHTR

3. Wiring and Parts
3.1
3.2
3.3
3.4
6
Cs Sample Capacitors
Rs Resistors
LED Traces and Other Switching Signals
PCB Cleanliness
AT42QT1040
Cs0 – Cs3 are the charge sensing sample capacitors; normally they are identical in nominal
value. The optimal Cs values depend on the corresponding keys electrode design, the thickness
of the panel and its dielectric constant. Thicker panels require larger values of Cs. Values can be
in the range 2.2 nF (for faster operation) to 22 nF (for best sensitivity); typical values are 4.7 nF
to 10 nF.
The value of Cs should be chosen such that a light touch on a key mounted in a production unit
or a prototype panel causes a reliable detection. The chosen Cs value should never be so large
that the key signals exceed ~1000, as reported by the chip in the debug data.
The Cs capacitors must be X7R or PPS film type, for stability. For consistent sensitivity, they
should have a 10 percent tolerance. Twenty percent tolerance may cause small differences in
sensitivity from key to key and unit to unit. If a key is not used, the Cs capacitor may be omitted.
The series resistors Rs0 – Rs3 are inline with the electrode connections (close to the QT1040
chip) and are used to limit electrostatic discharge (ESD) currents and to suppress radio
frequency (RF) interference. A typical value is 4.7 k, but up to 20 k can be used if it is found
to be of benefit.
Although these resistors may be omitted, the device may become susceptible to external noise
or radio frequency interference (RFI). For details on how to select these resistors refer to
Application Note QTAN0002, Secrets of a Successful QTouch
Design Guide, both downloadable from the Touch Technology area of Atmel’s website,
www.atmel.com.
For advice on LEDs and nearby traces, refer to Application Note QTAN0002, Secrets of a
Successful QTouch
the Touch Technology area of Atmel’s website, www.atmel.com.
Modern no-clean flux is generally compatible with capacitive sensing circuits.
If a PCB is reworked in any way, clean it thoroughly to remove all traces of the flux residue
around the capacitive sensor components. Dry it thoroughly before any further testing is
conducted.
CAUTION:
of the no-clean flux will change. This can mean that the flux changes from an inert
material to one that can absorb moisture and dramatically affect capacitive
measurements due to additional leakage currents. If so, the circuit can become
erratic and exhibit poor environmental stability.
™
If a PCB is reworked in any way, it is almost guaranteed that the behavior
Design, and the Touch Sensors Design Guide, both downloadable from
™
Design, and the Touch Sensors
9524B–AT42–04/09