QT110-ISG Atmel, QT110-ISG Datasheet
QT110-ISG
Specifications of QT110-ISG
Related parts for QT110-ISG
QT110-ISG Summary of contents
Page 1
... By using the charge transfer principle, the QT110 delivers a level of performance clearly superior to older technologies in a highly cost-effective package + +85 lq Appliance control Access systems Security systems Pointing devices AVAILABLE OPTIONS (Pb-FREE) SOIC QT110-ISG QT ™ S OUCH ENSOR Vdd 1 8 Out 2 7 Opt1 3 6 Opt2 4 5 Elevator buttons Consumer electronics 8-PIN DIP QT110-DG - © ...
Page 2
... X7R type changes with temperature, the internal drift compensation mechanism also adjusts for the drift automatically. Piezo sounder drive: The QT110 can drive a piezo sounder after a detection for feedback. The piezo sounder replaces or augments the Cs capacitor; this works since piezo sounders are also capacitors, albeit with a large thermal drift coefficient ...
Page 3
... S ENSITIVITY The QT110 can be set for one of 3 gain levels using option pin 5 (Table 1-1). If left open, the gain setting is high. The sensitivity change is made by altering the numerical threshold level required for a detection also a function of other ...
Page 4
... However, the supply drain is so low simple matter to treat the entire controllable load; simply driving the QT110's Vdd pin directly from another logic gate or a microprocessor port (Figure 2-2) will serve as both power and 'forced recal'. The source resistance of most CMOS gates and microprocessors is low enough to provide direct power without any problems ...
Page 5
... Out to ground (Figure 2-6). 2.2.6 O The QT110’s output is active low ; it can source 1mA or sink 5mA of non-inductive current. Care should be taken when the IC and the load are both powered from the same supply, and the supply is minimally regulated ...
Page 6
... Detection ‘stiction’, the opposite effect, can occur if a load is shed when Out is active. The output of the QT110 can directly drive a resistively limited LED. The LED should be connected with its cathode to the output and its anode towards Vcc, so that it lights when the sensor is active-low ...
Page 7
... Maximize Re to the limit where sensitivity is not affected not place the electrode or its connecting trace near other traces, or near a ground plane use a ground plane under and around the QT110 itself, back to the regulator and power connector (but not beyond the Cs capacitor). ...
Page 8
... unless otherwise noted. Min Typ Max 3.1 4.7 6. 750 +125 X7R ceramic Notes ms µ 5.0V Vdd ms @ 3.3V Vdd ms ms kHz ms ms µs kHz Units Notes % Note 1 % Note 1 % Note 1 % Note 2 samples ms/level ms/level secs Note 3 QT110 R1.04/0405 O C ...
Page 9
... Figure 4-2 Medium Gain Sensitivity and Range @ Vdd = 3V 4.0 3.0 2.0 1.0 Valid operating range 10 20 Cs, nF Figure 4-4 Typical Supply Current Vs Vdd Rs = 470K 10pF, Gain = High 20nF 10nF 10 5 2.5 3 3.5 Vdd QT110 R1.04/0405 Cx=30pF 25pF 20pF 10pF 5pF 0pF 30 4 4.5 5 ...
Page 10
... Inches Min Max 0.189 0.196 0.229 0.244 0.15 0.157 0.054 0.068 0.004 0.01 0.050 0.05 0.014 0.019 0.02 0.04 0.007 0.01 0.229 0.03 0º 8º QT110 R1.04/0405 Notes Typical BSC Typical BSC Notes BSC ...
Page 11
... ORDERING INFORMATION PART QT110-DG QT110-ISG LQ TEMP RANGE PACKAGE 0 - 70C PDIP Lead-Free -40 - 85C SOIC-8 Lead-Free 11 MARKING QT1 + 10G or QT110-G QT1 + IG or QT110-IG QT110 R1.04/0405 ...
Page 12
Tel: +44 (0)23 8056 5600 Fax: +44 (0)23 8045 3939 This device covered under one or more of the following United States and international patents: 5,730,165, 6,288,707, 6,377,009, 6,452,514, 6,457,355, 6,466,036, 6,535,200. Numerous further patents are pending which may ...