DS99R106SQX/NOPB National Semiconductor, DS99R106SQX/NOPB Datasheet - Page 17
![IC DESERIALIZ 40MHZ 24BIT 48LLP](/photos/6/92/69244/pkg_sqa48d_sml.jpg)
DS99R106SQX/NOPB
Manufacturer Part Number
DS99R106SQX/NOPB
Description
IC DESERIALIZ 40MHZ 24BIT 48LLP
Manufacturer
National Semiconductor
Datasheet
1.DS99R106SQNOPB.pdf
(24 pages)
Specifications of DS99R106SQX/NOPB
Function
Deserializer
Data Rate
960Mbps
Input Type
LVTTL/LVCMOS
Output Type
LVDS
Number Of Inputs
1
Number Of Outputs
24
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
48-LLP
Number Of Elements
1
Number Of Receivers
1
Number Of Drivers
24
Operating Supply Voltage (typ)
3.3V
Differential Input High Threshold Voltage
50mV
Diff. Input Low Threshold Volt
-50mV
Transmission Data Rate
960Mbps
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
48
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
DS99R106SQX
must monitor the LOCK pin to determine whether data on the
ROUT is valid.
POWERDOWN
The Powerdown state is a low power sleep mode that the Se-
rializer and Deserializer may use to reduce power when no
data is being transferred. The TPWDNB and RPWDNB are
used to set each device into power down mode, which re-
duces supply current to the µA range. The Serializer enters
powerdown when the TPWDNB pin is driven low. In power-
down, the PLL stops and the outputs go into TRI-STATE,
disabling load current and reducing supply. To exit Power-
down, TPWDNB must be driven high. When the Serializer
exits Powerdown, its PLL must lock to TCLK before it is ready
for the Initialization state. The system must then allow time for
Initialization before data transfer can begin. The Deserializer
enters powerdown mode when RPWDNB is driven low. In
powerdown mode, the PLL stops and the outputs enter TRI-
STATE. To bring the Deserializer block out of the powerdown
state, the system drives RPWDNB high.
Both the Serializer and Deserializer must reinitialize and re-
lock before data can be transferred. The Deserializer will
initialize and assert LOCK high when it is locked to the en-
coded clock.
TRI-STATE
For the Serializer, TRI-STATE is entered when the DEN or
TPWDNB pin is driven low. This will TRI-STATE both driver
output pins (DOUT+ and DOUT−). When DEN is driven high,
the serializer will return to the previous state as long as all
other control pins remain static (TPWDNB, TRFB).
When you drive the REN or RPWDNB pin low, the Deserial-
izer enters TRI-STATE. Consequently, the receiver output
pins (ROUT0–ROUT23) and RCLK will enter TRI-STATE.
The LOCK output remains active, reflecting the state of the
PLL. The Deserializer input pins are high impedance during
receiver powerdown (RPWDNB low) and power-off (V
0V).
PRE-EMPHASIS
The DS99R105 features a Pre-Emphasis mode used to com-
pensate for long or lossy transmission media. Cable drive is
enhanced with a user selectable Pre-Emphasis feature that
provides additional output current during transitions to coun-
teract cable loading effects. The transmission distance will be
limited by the loss characteristics and quality of the media.
Pre-Emphasis adds extra current during LVDS logic transition
to reduce the cable loading effects and increase driving dis-
tance. In addition, Pre-Emphasis helps provide faster transi-
tions, increased eye openings, and improved signal integrity.
The ability of the DS99R105 to use the Pre-Emphasis feature
will extend the transmission distance in most cases.
AC-COUPLING AND TERMINATION
The DS99R105 and DS99R106 supports AC-coupled inter-
connects through integrated DC balanced encoding/decoding
scheme. To use AC coupled connection between the Serial-
izer and Deserializer, insert external AC coupling capacitors
in series in the LVDS signal path as illustrated in Figure 17.
The Deserializer input stage is designed for AC-coupling by
providing a built-in AC bias network which sets the internal
V
ac-coupling path to the signal input.
For the high-speed LVDS transmissions, the smallest avail-
able package should be used for the AC coupling capacitor.
This will help minimize degradation of signal quality due to
CM
to +1.2V. With AC signal coupling, capacitors provide the
DD
=
17
package parasitics. The most common used capacitor value
for the interface is 100 nF (0.1 uF) capacitor.
A termination resistor across DOUT± is also required for
proper operation to be obtained. The termination resistor
should be equal to the differential impedance of the media
being driven. This should be in the range of 90 to 132 Ohms.
100 Ohms is a typical value common used with standard 100
Ohm transmission media. This resistor is required for control
of reflections and also to complete the current loop. It should
be placed as close to the Serializer DOUT± outputs to mini-
mize the stub length from the pins. To match with the defer-
ential impedance on the transmission line, the LVDS I/O are
terminated with 100 ohm resistors on Serializer DOUT± out-
puts pins.
PROGRESSIVE TURN–ON (PTO)
Deserializer ROUT[23:0] outputs are grouped into three
groups of eight, with each group switching about 0.5UI apart
in phase to reduce EMI, simultaneous switching noise, and
system ground bounce.
Applications Information
USING THE DS99R105 AND DS99R106
The
(SERDES) pair sends 24 bits of parallel LVCMOS data over
a serial LVDS link up to 960 Mbps. Serialization of the input
data is accomplished using an on-board PLL at the Serializer
which embeds clock with the data. The Deserializer extracts
the clock/control information from the incoming data stream
and deserializes the data. The Deserializer monitors the in-
coming clockl information to determine lock status and will
indicate lock by asserting the LOCK output high.
POWER CONSIDERATIONS
An all CMOS design of the Serializer and Deserializer makes
them inherently low power devices. Additionally, the constant
current source nature of the LVDS outputs minimize the slope
of the speed vs. I
NOISE MARGIN
The Deserializer noise margin is the amount of input jitter
(phase noise) that the Deserializer can tolerate and still reli-
ably recover data. Various environmental and systematic fac-
tors include:
of-band noise)
For a graphical representation of noise margin, please see
Figure 16.
TRANSMISSION MEDIA
The Serializer and Deserializer can be used in point-to-point
configuration, through a PCB trace, or through twisted pair
cable. In a point-to-point configuration, the transmission me-
dia needs be terminated at both ends of the transmitter and
receiver pair. Interconnect for LVDS typically has a differential
impedance of 100 Ohms. Use cables and connectors that
have matched differential impedance to minimize impedance
discontinuities. In most applications that involve cables, the
transmission distance will be determined on data rates in-
volved, acceptable bit error rate and transmission medium.
Serializer: TCLK jitter, V
Media: ISI, V
Deserializer: V
DS99R105/DS99R106
CM
DD
DD
noise
noise
curve of CMOS designs.
DD
noise (noise bandwidth and out-
Serializer/Deserializer
www.national.com