MCZ33972AEK Freescale Semiconductor, MCZ33972AEK Datasheet - Page 21
![IC MULTIPLE SWITCH DETECT 32SOIC](/photos/6/93/69328/mcz33972aek_sml.jpg)
MCZ33972AEK
Manufacturer Part Number
MCZ33972AEK
Description
IC MULTIPLE SWITCH DETECT 32SOIC
Manufacturer
Freescale Semiconductor
Datasheet
1.MCZ33972AEK.pdf
(32 pages)
Specifications of MCZ33972AEK
Applications
Switch Monitoring
Interface
SPI
Voltage - Supply
8 V ~ 26 V
Package / Case
32-SOIC (7.5mm Width) Exposed Pad, 32-eSOIC, 32-HSOIC
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCZ33972AEK
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MCZ33972AEKR2
Manufacturer:
FREESCALE
Quantity:
20 000
closed switch contacts. However, there are many features
that allow the device to be used in a variety of applications.
The following is a list of applications to consider for the IC:
detail.
SENSOR POWER SUPPLY
external to a module. Many sensors such as Hall effect,
pressure sensors, and temperature sensors require a supply
voltage to power the sensor and provide an open collector or
analog output.
to supply power and interface to these types of sensors. In an
application where the input makes continuous transitions,
consider using the wake-up / interrupt command to disable
the interrupt for the particular input.
Analog Integrated Circuit Device Data
Freescale Semiconductor
Reg
X
The 33972’s primary function is the detection of open or
Sensor Power Supply
Switch Monitor for Metallic or Elastomeric Switches
Analog Sensor Inputs (Ratiometric)
Power MOSFET / LED Driver and Monitor
Multiple 33972 Devices in a Module System
The following paragraphs describe the applications in
Each input may be used to supply current to sensors
V
Hall-Effect
Sensor
V
16 mA
BAT
BAT
SG12
SG13
SG0
SG1
Figure 13. Sensor Power Supply
SP0
SP7
SP1
Figure 13
16
mA
16
mA
V
V
PWR
PWR
V
V
33972
shows how the 33972 may be used
PWR
PWR
2.5 kΩ
2.0
mA
2.0
mA
WAKE
VPWR
SCLK
VDD
2.5 kΩ
INT
CS
SO
SI
V
DD
MOSI
SCLK
CS
MISO
INT
TYPICAL APPLICATIONS
IOC[7:0]
Input Capture
Timer Port
MCU
INTRODUCTION
METALLIC / ELASTOMERIC SWITCH
resistance over time owing to contact corrosion. The
corrosion is induced by humidity, salt, and other elements
that exist in the environment. For this reason the 33972
provides two settings for contacts. When programmed for
metallic switches, the device provides higher wetting current
to keep switch contacts free of oxides. The higher current
occurs for the first 20 ms of switch closure. Where longer
duration of wetting current is desired, the user may send the
wetting current timer command and disable the timer. Wetting
current will be continuous to the closed switch. After the time
period set by the MCU, the wetting current timer command
may be sent again to enable the timer. The user must
consider power dissipation on the device when disabling the
timer. (Refer to the paragraph entitled
page 20.)
contact, the user has two options. Higher wetting current to a
switch may be achieved by paralleling SGn or SPn inputs.
This will increase wetting current by 16 mA for each input
added to the switch contact. The second option is to simply
add an external resistor pull-up to the V
to-ground inputs or a resistor to ground for a switch-to-battery
input. Adding an external resistor has no effect on the
operation of the device.
a high contact resistance. Resistance of 1.0 kΩ is common.
In applications with elastomeric switches, the pull-up and
pulldown currents must be reduced to prevent excessive
power dissipation at the contact. Programming for a lower
current settings is provided in the
Operation
Metallic Command.
ANALOG SENSOR INPUTS (RATIOMETRIC)
the binary code for a specific input in the analog command
allows the microcontroller to perform analog to digital
conversion on any of the 22 inputs. On rising edge of
multiplexer connects a requested input to the AMUX pin. The
AMUX pin is clamped to max of V
higher voltages present on the input pin. After an input has
been selected as the analog, the corresponding bit in the next
SO data stream will be logic [0].
configured as analog with high-impedance, analog with
2.0 mA pull-up, or analog with 16 mA pull-up.
page 22, shows how the 33972 may be used to provide a
ratiometric reading of variable resistive input.
Metallic switch contacts often develop higher contact
To increase the amount of wetting current for a switch
Elastomeric switch contacts are made of carbon and have
The 33972 features a 22-to-1 analog multiplexer. Setting
The input pin, when selected as analog, may be
section beginning on page
Functional Device
DD
TYPICAL APPLICATIONS
volts regardless of the
13
Temperature
PWR
under
supply for switch-
INTRODUCTION
Figure
Table
Monitor,
14,
CS
8,
33972
the
21