UJA1065TW/3V0,518 NXP Semiconductors, UJA1065TW/3V0,518 Datasheet - Page 38
![IC CAN/LIN FAIL-SAFE 32HTSSOP](/photos/6/94/69422/uja1065_hq_sml.jpg)
UJA1065TW/3V0,518
Manufacturer Part Number
UJA1065TW/3V0,518
Description
IC CAN/LIN FAIL-SAFE 32HTSSOP
Manufacturer
NXP Semiconductors
Datasheet
1.UJA1065TW3V3CT.pdf
(76 pages)
Specifications of UJA1065TW/3V0,518
Package / Case
32-TSSOP Exposed Pad, 32-eTSSOP, 32-HTSSOP
Applications
Networking
Interface
CAN, LIN
Voltage - Supply
5.5 V ~ 52 V
Mounting Type
Surface Mount
Product
Controller Area Network (CAN)
Number Of Transceivers
1
Data Rate
20 Kbps
Supply Voltage (max)
27 V, 52 V
Supply Voltage (min)
5.5 V
Supply Current (max)
10 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-4372-2
935281289518
UJA1065TW/3V0-T
UJA1065TW/3V0-T
935281289518
UJA1065TW/3V0-T
UJA1065TW/3V0-T
NXP Semiconductors
Table 11.
[1]
[2]
UJA1065_7
Product data sheet
Bit
15 and 14
13
12
11 and 10
9
8
7 and 6
5
4
3
2
1
0
RLC is set automatically with entering Restart mode or Fail-safe mode. This guarantees a safe reset period in case of serious failure
situations. External reset spikes are lengthened by the SBC until the programmed reset length is reached.
If WEN is not set, the WAKE port is completely disabled. There is no change of the bits EWS and WLS within the System Status register.
System Configuration and System Configuration Feedback register bit description
Symbol
A1, A0
RRS
RO
-
GSTHC
RLC
V3C[1:0]
-
V1CMC
WEN
WSC
ILEN
ILC
6.13.8 System Configuration register and System Configuration Feedback register
These registers allow configuration of the behavior of the SBC, and allow the settings to
be read back.
Description
register address
Read Register Select
Read Only
reserved
GND Shift Threshold
Control
Reset Length Control
V3 Control
reserved
V1 Current Monitor
Control
Wake Enable
Wake Sample Control
INH/LIMP Enable
INH/LIMP Control
[2]
Rev. 07 — 25 February 2010
Value
10
1
0
0
1
0
1
0
11
10
01
00
0
1
0
1
0
1
0
0
1
0
1
0
1
[1]
Function
select System Configuration register
read the General Purpose Feedback register 0
read the System Configuration Feedback register
read register selected by RRS without writing to System
Configuration register
read register selected by RRS and write to System
Configuration register
reserved for future use; should remain cleared to ensure
compatibility with future functions which might use this bit
V
V
t
t
Cyclic mode 2; t
Cyclic mode 1; t
continuously ON
OFF
reserved for future use; should remain cleared to ensure
compatibility with future functions which might use this bit
an increasing V1 current causes a reset if the watchdog
was disabled during Standby mode
an increasing V1 current just reactivates the watchdog
during Standby mode
WAKE pin enabled
WAKE pin disabled
Wake mode cyclic sample
Wake mode continuous sample
INH/LIMP pin active (See ILC bit)
INH/LIMP pin floating
INH/LIMP pin HIGH if ILEN bit is set
INH/LIMP pin LOW if ILEN bit is set
RSTNL
RSTNL
th(GSD)(cm)
th(GSD)(cm)
High-speed CAN/LIN fail-safe system basis chip
long reset lengthening time selected
short reset lengthening time selected
widened threshold
normal threshold
w(CS)
w(CS)
long period; see
short period; see
Figure 14
UJA1065
Figure 14
© NXP B.V. 2010. All rights reserved.
38 of 76