D4NL-4EDA-B4-NPT Omron, D4NL-4EDA-B4-NPT Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
D4NL-4EDA-B4-NPT
Manufacturer Part Number
D4NL-4EDA-B4-NPT
Description
Basic / Snap Action / Limit Switches 3NC+1NC/1NO Metal head SOL.RLS
Manufacturer
Omron
Series
D4NLr
Datasheet
1.D4NL-1CFGB.pdf
(18 pages)
Specifications of D4NL-4EDA-B4-NPT
Lead Free Status / Rohs Status
Details
Wiring Precautions
Processing the Conduit Opening
[Reference] The terminals listed below have thickness of 0.5 mm or
• Do not wire the Switch while power is being
• Do not let particles, such as small pieces of lead
• When connecting to the terminals via insulating
• Applicable lead wire size: AWG20 to AWG18 (0.5 to 0.75 mm
• Do not push crimp terminals into gaps in the case interior. Doing so
• Use terminals having the thickness of 0.5 mm or less to avoid the
J.S.T. Mfg Co.
• Connect a recommended connector to the opening of the conduit
• When using a 1/2-14NPT conduit, wind sealing tape around the
• Make sure that the outer diameter of the cable connected to the
• Attach a conduit cap to the unused conduit opening when wiring
supplied. Doing so may result in electric shock.
wire, enter the switch body when wiring.
tube and M3.5 crimp terminals, cross the crimp
terminals as shown above so that they do not rise
up onto the case or the cover.
Use lead wires of an appropriate length. Not doing so may result in
excess length causing the cover to rise and not fit properly.
may cause damage or deformation of the case.
contact between the terminal and the interior of the Switch case.
and tighten the connector to the proper torque. The case may be
damaged if excessive tightening torque is applied.
conduit end of the connector so that the enclosure will conform to
IP67.
connector is correct.
and tighten it to a suitable torque. The conduit cap is provided with
the Switch.
Manufacturer
less.
FN0.5-3.7 (F Type)
No. 5-3.7 (Straight Type)
D dia.
Model
dz dia.
2
).
Recommended Connectors
• Use a connector with a screw section not exceeding 11 mm.
• When using the 1/2-14NPT conduit, mount the adaptor that comes
1/2-14NPT
Otherwise the screws will protrude into the case interior. The
connectors given in the following table have connectors with screw
sections not exceeding 11 mm.
Use the following connectors to ensure conformance to IP67.
Pg13.5
Use LAPP connectors together with Seal Packing (JPK-16,
GP-13.5, or GPM20), and tighten to the applicable torque. Seal
Packing is sold separately.
• LAPP is a German manufacturer.
• OHM Electric Co. is a Japanese manufacturer.
with it to the Switch, then wind sealing tape around it to use the
connector listed above.
G1/2
Size
M20
ELECTRIC CO.
Manufacturer
LAPP
LAPP
LAPP
LAPP
OHM
ST-PF1/2
5380-1002
OA-W1609
OA-W1611
ST-13.5
5301-5030
ST-M20 × 1.5
5311-1020
ST-NPT1/2
5301-6030
Model
Applicable cable
6.0 to 12.0 mm
9.0 to 11.0 mm
6.0 to 12.0 mm
7.0 to 13.0 mm
6.0 to 12.0 mm
7.0 to 9.0 mm
diameter
D4NL
17