MC33884DW Freescale Semiconductor, MC33884DW Datasheet - Page 10

• Manufacturer Part Number: MC33884DW
• Description: IC SWITCH SDI MONITOR 24-SOIC
• Manufacturer: Freescale Semiconductor

Specifications of MC33884DW

• Applications: *
• Interface: *
• Voltage - Supply: *
• Package / Case: 24-SOIC (7.5mm Width)
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

CHIP SELECT (CS)
communication through the Chip Select (CS) pin. With the CS
in a logic low state, command words may be sent to the
33884 via the Serial Input (SI) pin. Switch status is received
by the MCU via Serial Output (SO) pin. The falling edge of CS
enables the SO output, latches the state of the Interrupt (INT)
pin, Operating mode and the state of the external switch
inputs. The rising edge of CS disables the SO driver, resets
the INT pin to logic [1], activates the received command word,
and allows the 33884 to act upon new data obtained from
switch inputs. To avoid any spurious data, it is essential the
high-to-low and low-to-high transition of the CS signal occur
only when System Clock (SCLK) is in a logic low state.
Internal to the 33884 is an active pull-up on CS pin.
SYSTEM CLOCK (SCLK)
Shift register. The Serial Input (SI) data is latched into the
Input Shift register on the rising edge of SCLK signal. The
Serial Output (SO) pin shifts the switch status bits out on the
falling edge of SCLK. False clocking of the Shift register must
be avoided to guarantee validity of data. It is essential the
SCLK pin be in a logic low state whenever CS makes any
transition. For this reason it is recommended, though not
necessary, the SCLK pin be commanded to a low logic state
as long as the device is not accessed (CS in logic high state).
When the CS is in a logic high state, any signal on the SCLK
and SI pin will be ignored and the SO pin is Tri-Stated (high
impedance).
10
33884
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
The MCU system selects the 33884 to receive its
The System Clock (SCLK) pin clocks the internal 16-bit
Figure 5. SPI Parallel Interface with Microprocessor
Microcontroller
16 Bit Shift Register
MC68HCXX
Parallel
Ports
SCLK
INT
MISO
MOSI
SI
SO
SCLK
CS
RST
INT
SI
SO
SCLK
CS
RST
INT
33884
33884
FUNCTIONAL PIN DESCRIPTION
SERIAL INPUT (SI)
input. SI information is latched into the Input register on the
rising edge of SCLK. A logic high state present at SI when
SCLK rises, programs a logic [1] into the command word on
rising edge of the CS signal. To program a complete word, 16
bits of information must be entered into the 33884. Internal to
the IC is an active pull down on the SI pin.
SERIAL OUTPUT (SO)
register. The SO pin remains Tri-Stated until the CS pin
transitions to a logic low state. All open switches are reported
as logic [0], all closed switches are reported as logic [1]. The
negative transition of CS will make status bit 15 available on
SO. Each successive negative clock makes the next status
bit available. The SI/SO shifting of the data follows a first-in-
first-out protocol with both input and output words transferring
the most significant bit (MSB) first.
MASTER/SLAVE (MASL)
33884 devices are used in one module. The MASL identifies
which device will be the master or slave. MASL identification
is used during the Polling mode. In the Polling mode, the
master device has it’s internal oscillator running while the
Slave device oscillator is shutdown. While polling, the master
device wakes the slave via the Synchronization (SYNC) pin.
This feature provides minimal quiescent from the voltage
power (VPWR) and voltage digital drain (VDD) pins.
This Serial Input (SI) pin is used for serial instruction data
The Serial Output (SO) pin is the output from the Shift
The Master/Slave (MASL) pin is required when multiple
Figure 6. SPI Serial Interface with Microprocessor
Microcontroller
16 Bit Shift Register
MC68HCXX
Parallel
Ports
SCLK
INT
Analog Integrated Circuit Device Data
MOSI
MISO
Freescale Semiconductor
SI
SO
SCLK
CS
RST
INT
SI
SO
SCLK
CS
RST
INT
33884
33884