R88M-W75030H-BS1 Omron, R88M-W75030H-BS1 Datasheet - Page 114
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-W75030H-BS1
Manufacturer Part Number
R88M-W75030H-BS1
Description
SERVOMOTOR 750W 3000RPM INC BK K
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-W75030H-BS1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MW75030HBS1
- Current page: 114 of 458
- Download datasheet (5Mb)
Standard Models and Specifications
The following diagram shows the output phases. (The phases are the same for both absolute and incre-
mental encoders.)
Note 1. Phase Z is synchronous with phase A.
Note 2. The speed of the initial incremental pulses depends on the Servo Driver software version. If
D Alarm Code Outputs 1 to 3 (37: ALO1; 38: AL02; 39: ALO3)
When a Servo Driver error is detected, the contents of the error are output in 3-bit code. The alarm code
output ground common is CN1 pin 1 (GND). For details, refer to 5-2 Alarms .
D Alarm Output (31: ALM)
When the Servo Driver detects an error, outputs are turned OFF. At that time, an alarm code is output
according to the contents of the error. This output is OFF at the time of powering up, and turns ON when
the initial processing is completed.
D Positioning Completed Output 1 (25: INP1)
The INP1 signal turns ON when the number of accumulated pulses in the deviation counter is less than
Pn500 (positioning completed range 1). The INP2 signal turns ON when the number of pulses is less
than Pn504 (positioning completed range 2). These signals are always OFF when the control mode is
any mode other than the position control mode.
Note 1. These are the default allocations. The INP1 signal is allocated by Pn50E.0, and the INP2 sig-
Note 2. With the default allocations, INP1 (enabled for position control) and VCMP (enabled for speed
D Speed Conformity Output (25: VCMP)
The VCMP signal turns ON when the difference between the speed command and the Servomotor rota-
tion speed is equal to or less than the value set for Pn503 (speed conformity signal output width). For
example, if the speed command is for 3,000 r/min and the set value is for 50 r/min, it turns ON when the
2-86
Alarm Output Ground (32: ALMCOM)
Positioning Completed Output 1 Common (26: INP1COM)
Positioning Completed Output 2 (Not Allocated: INP2)
Speed Conformity Output Common (26: VCMPCOM)
Phase A
Phase B
Phase Z
the software version is “r0014,” the speed will be equivalent to approximately 2,500 r/min for
3,000-r/min motors and to approximately 1,000 r/min for 1,000-r/min motors. If the software
version is “r0008,” the speed will be equivalent to approximately 2,500 r/min. (Same for all
motors.)
nal is allocated by Pn510.0.
control) are allocated to CN1 pins 25 and 26.
Forward Rotation Side
Phase A
Phase B
Phase Z
Reverse Rotation Side
Chapter 2
Related parts for R88M-W75030H-BS1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: