R88M-WP75030T-S1 Omron, R88M-WP75030T-S1 Datasheet - Page 395
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-WP75030T-S1
Manufacturer Part Number
R88M-WP75030T-S1
Description
SERVO MOTOR 750W 200V
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-WP75030T-S1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MWP75030TS1
- Current page: 395 of 458
- Download datasheet (5Mb)
Troubleshooting
Computer Monitor Software
5-1-2 Precautions
H Precautions
• Disconnect any cables before checking if they have burned out. Even if you have checked the conduc-
• If the encoder signal is lost, the Servomotor may run away, or an error may be generated. Make sure
• When measuring the encoder output, measure using the ground (CN1-1 pin) as standard. If measur-
• When performing tests, first check that there are no personnel inside the machine facilities, and that
5-1-3 Replacing the Servomotor and Servo Driver
H Replacing the Servomotor
1. Replace the Servomotor.
2. Perform origin teaching (if using position control).
3. Set up the absolute encoder (ABS).
tion of the wiring, there is a risk of conduction due to the return circuit.
the Servomotor is disconnected from the mechanical system before checking the encoder signal.
ing using an oscilloscope, measure using the differential between CH1 and CH2 to reduce interfer-
ence from noise.
the facilities will not be damaged even if the Servomotor runs away. Also, check that even if the Servo-
motor runs away, you can immediately stop the machine using an emergency stop before performing
the tests.
Note Refer to 4-2-2 Absolute Encoder Setup and Battery Changes for details.
S Install and use the OMNUC W-series Servo Driver Computer Monitor Software (for Windows 95).
S Refer to the Computer Monitor Software for operation details.
S When replacing the Servomotor, the Servomotor’s specific origin position (Z-phase) may slip, so
S Refer to the manual for the position controller you use for how to perform origin teaching.
S If using a Servomotor with an absolute encoder, when replacing the Servomotor, the absolute data
The following three items are required: An IBM PC/AT or compatible with Windows 95, the Com-
puter Monitor Software, and Connecting Cable (R88A-CCW002Pj).
be sure to perform origin teaching.
in the absolute encoder will be cleared, so you need to set up the data again. Also, the rotation limit
data will be different from before you replaced the Servomotor, so initialize the Motion Control Unit
settings.
When checking and verifying I/O after trouble has occurred, the Servo Driver may sud-
denly start to operate or suddenly stop, so take precautions. Also, do not attempt opera-
tions not specified in this manual.
Perform the following procedure to replace the Servomotor or Servo Driver.
Chapter 5
5-3
Related parts for R88M-WP75030T-S1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: