PD15-22B/TR8 Everlight Electronics Co Ltd, PD15-22B/TR8 Datasheet
PD15-22B/TR8
Specifications of PD15-22B/TR8
Available stocks
Related parts for PD15-22B/TR8
PD15-22B/TR8 Summary of contents
Page 1
... RoHS compliant version. Descriptions ․PD15-22B/TR8 is a high speed and high sensitive PIN photodiode in miniature flat top view lens SMD package and it is molded in a black plastic. The device is Spectrally matched to visible and infrared emitting diode ...
Page 2
... Everlight Electronics Co., Ltd. Device No ： D TD-152-002 2.1 2.0 3.3 2.3 4-R0.25 Symbol Rating -40 ~ +85 opr T -40 ~ +100 stg *1 T 260 sol P 150 c http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 2.1 1.2 Units V ℃ ℃ ℃ mW Rev 2 Page Prepared by ： D aniel Yang ...
Page 3
... P Ee=1mW /cm λ =875nm =5V R Ee=0mW / =10V R Ee=0mW / =100μA R Ee=0mW /cm C f=1MHz =1000Ω http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 Min Typ Max 730 --- 1100 --- 940 --- 2 --- 0.41 --- 2 4.0 6.5 --- 2 4.2 6.5 --- 2 --- --- 170 --- 2 --- 6 --- --- 10 --- --- 10 --- Rev 2 Page Prepared by ： ...
Page 4
... D TD-152-002 Fig.2 Spectral Sensitivity 1.0 0 100 Fig.4 Reverse Light Current vs =10V 100 http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 O C Ta=25 700 750 800 850 900 950 Ee V 0.5 1.5 1.0 2 Rev 2 Page Prepared by ： D aniel Yang 1100 1000 1050 =5V R ...
Page 5
... Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Reverse Voltage 0.1 1 Everlight Electronics Co., Ltd. Device No ： D TD-152-002 Fig.6 Response Time vs f=1MH 100 10 http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 Load Resistance V =10V R Ta=25° Rev 2 Page Prepared by ： D aniel Yang ...
Page 6
... Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No ： D TD-152-002 http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 Rev 2 Page Prepared by ： D aniel Yang ...
Page 7
... Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No ： D TD-152-002 http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 Rev 2 Page Prepared by ： D aniel Yang ...
Page 8
... Test Hours/ Cycles 6Mins 15mins 50Cycles 5mins 15mins 5mins 50Cycles 10secs 5mins 1000hrs 1000hrs =5V 1000hrs R 1000hrs http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 Sample Failure Sizes Judgement Criteria 22pcs ≦L×0 22pcs L：Lower Specification Limit 22pcs 22pcs 22pcs 22pcs 22pcs Rev 2 Page Prepared by ： ...
Page 9
... Carrier Tape Dimensions:(Quantity: 2000pcs/reel) 2.0±0.05 4.0 Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No ： D TD-152-002 4.0 1.55±0. Anode 1 2.95 2 Cathode http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 0.23 1.65 Rev 2 Page Prepared by ： D aniel Yang ...
Page 10
... P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date ： 0 2-26-2008 PD15-22B/TR8 Label Rev 2 Page Prepared by ： D aniel Yang ...