MT9234ZPX-UPCI-CP Multi-Tech Systems, MT9234ZPX-UPCI-CP Datasheet - Page 54

• Manufacturer Part Number: MT9234ZPX-UPCI-CP
• Description: MODEM V.92 DATA/FAX/VOICE WORLD
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® ZPXr

Specifications of MT9234ZPX-UPCI-CP

• Data Format: V.92
• Baud Rates: -
• Interface: Parallel
• Voltage - Supply: 3.3V, 5V
• Mounting Type: Socket
• Package / Case: 6.0" L x 4.8" W x 0.7" H (152mm x 122mm x 18mm)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Appendix B – Regulatory Compliance
EMC, Safety, and R&TTE Directive Compliance
The CE mark is affixed to this product to confirm compliance with the following European Community Directives:
New Zealand Telecom Warning Notice
54
1.
2.
3.
4.
5.
6.
7.
8.
Council Directive 2004/108/EC of 15 December 2004 on the approximation of the laws of Member States
relating to electromagnetic compatibility;
And
Council Directive 2006/95/EC of 12 December 2006 on the harmonization of the laws of Member States
relating to electrical equipment designed for use within certain voltage limits;
And
Council Directive 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal
equipment and the mutual recognition of their conformity.
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that
the item complies with minimum conditions for connection to its network. It indicates no endorsement of the
product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any
item will work correctly in all respects with another item of Telepermitted equipment of a different make or
model, nor does it imply that any product is compatible with all of Telecom’s network services.
This equipment is not capable under all operating conditions of correct operation at the higher speed which
it is designated. 33.6 kbps and 56 kbps connections are likely to be restricted to lower bit rates when
connected to some PSTN implementations. Telecom will accept no responsibility should difficulties arise in
such circumstances.
Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal
or repair.
This modem shall not be used in any manner which could constitute a nuisance to other Telecom
customers.
This device is equipped with pulse dialing, while the Telecom standard is DTMF tone dialing. There is no
guarantee that Telecom lines will always continue to support pulse dialing.
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise
to ‘bell tinkle’ or noise and may also cause a false answer condition. Should such problems occur, the user
should not contact the Telecom Faults Service.
The preferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic) dialing and is
readily available on almost all New Zealand telephone exchanges.
Warning Notice: No ‘111’ or other calls can be made from this device during a mains power failure.
This equipment may not provide for the effective hand-over of a call to another device connected to the
same line.
Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the
equipment (PC) associated with this device. The associated equipment shall be set to operate within the
following limits for compliance with Telecom’s Specifications:
For repeat calls to the same number:
●
●
For automatic calls to different numbers:
●
For automatically answered incoming calls:
●
For correct operation, total of the RNs of all devices connected to a single line at any time should not
exceed 5.
There shall be no more than 10 call attempts to the same number within any 30-minute period for any
single manual call initiation, and
The equipment shall go on-hook for a period of not less than 30 seconds between the end of one
attempt and the beginning of the next attempt.
The equipment shall be set to ensure that automatic calls to different numbers are spaced such that
there is no less than 5 seconds between the end of one call attempt and the beginning of another.
The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of
ringing.
Multi-Tech Systems, Inc. MT9234ZPX User Guide