MAX396CAI+ Maxim Integrated Products, MAX396CAI+ Datasheet - Page 7

• Manufacturer Part Number: MAX396CAI+
• Description: IC MULTIPLEXER 16X1 28SSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX396CAI+

• Function: Multiplexer
• Circuit: 1 x 16:1
• On-state Resistance: 100 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 2.7 V ~ 16 V, ±2.7 V ~ 8 V
• Current - Supply: 0.08µA, 0.06µA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Using supply voltages less than ±5V reduces the analog
signal range. The MAX396/MAX397 multiplexers (muxes)
operate with ±3V to ±8V bipolar supplies or with a +3V to
+15V single supply. Connect V- to GND when operating
with a single supply. Both devices can also operate with
unbalanced supplies, such as +10V and -5V. The Typical
Operating Characteristics graphs show typical on-
resistance with ±3V, ±5V, +3V, and +5V supplies.
(Switching times increase by a factor of two or more for
operation at 5V or below.)
These muxes operate with a single supply as low as 1V,
although on-resistance and switching times become
extremely high. Performance is not guaranteed below
2.7V. This is useful information only because it assures
proper switch state while power supplies ramp up or
down slowly.
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, NO, or COM. If power-supply sequencing
*Analog signal inputs and outputs are names of convenience only; they are identical and interchangeable.
______________________________________________________________Pin Description
__________Applications Information
MAX396
2, 3, 13
14–17
19–26
4–11
—
—
—
12
—
18
—
27
28
—
1
PIN
Operation with Supply Voltages
_______________________________________________________________________________________
Low-Voltage, CMOS Analog Multiplexers
15, 16, 17
MAX397
3, 13, 14
19–26
4–11
12
18
27
28
—
—
—
—
—
1
2
Precision, 16-Channel/Dual 8-Channel,
Overvoltage Protection
Other than ±5V
NO8B–NO1B
NO1A–NO8A
NO16–NO9
A2, A1, A0
NO1–NO8
COMB
COMA
NAME
A3–A0
COM
GND
N.C.
N.C.
EN
V+
V-
Positive Supply-Voltage Input
No Internal Connection
Analog Signal B Output* (bidirectional)
No Internal Connection
Analog Signal Inputs* (bidirectional)
Analog Signal B Inputs* (bidirectional)
Logic Ground
Logic Address Inputs
Logic Address Inputs
Logic Enable Input
Analog Signal Inputs* (bidirectional)
Analog Signal A Inputs* (bidirectional)
Negative Supply-Voltage Input
Analog Signal Output* (bidirectional)
Analog Signal A Output* (bidirectional)
Figure 1. Overvoltage Protection Using External Blocking Diodes
is not possible, add two small-signal diodes (D1, D2) in
series with supply pins for overvoltage protection
(Figure 1). Adding diodes reduces the analog-signal
range to one diode drop below V+ and one diode drop
above V-, but does not affect the devices’ low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between
V+ and V- should not exceed 17V. These protection
diodes are not recommended when using a single supply.
COM
FUNCTION
*
*
V+
V-
-5V
+5V
D1
D2
*INTERNAL PROTECTION DIODES
*
*
MAX396
MAX397
NO
7