SI2457-D-FT Silicon Laboratories Inc, SI2457-D-FT Datasheet - Page 26
SI2457-D-FT
Manufacturer Part Number
SI2457-D-FT
Description
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer
Silicon Laboratories Inc
Specifications of SI2457-D-FT
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 26 of 304
- Download datasheet (5Mb)
AN93
Bit 6 (TXE) is a read/write bit that gives the status of the 14-byte deep transmit FIFO. If TXE = 0, the transmit FIFO
contains three or more bytes. If TXE = 1, the transmit FIFO contains two or fewer bytes. Writing TXE = 0 clears the
interrupt but does not change the state of TXE.
Bit 5 (REM) is a read-only bit that indicates when the receive FIFO is empty. If REM = 0, the receive FIFO contains
valid data. If REM = 1, the receive FIFO is empty. The timer interrupt set by U6F ensures that the receive FIFO
contents 9 bytes are serviced properly.
Bit 4 (INTM) is a read/write bit that controls whether or not INT (bit 3) triggers the INT pin.
Bit 3 (INT) is a read-only bit that reports Interrupt status. If INT = 0, no interrupt has occurred. If INT = 1, an
interrupt due to CID, OCD, PPD, RI, or DCD (U70 bits 4, 3, 2, 1, 0, respectively) has occurred. This bit is reset by :I.
Bit 2 (ESC) is a read/write bit that is functionally equivalent to the ESC pin in the serial mode. The operation of this
bit, like the ESC pin, is enabled by setting U70 [15] (HES) = 1.
The use of bits 1 and 0 (RTS and CTS) has been deprecated for both parallel and SPI interfaces. Instead, the use
of bits 6 and 5 (TXE and REM) is recommended for polling- and interrupt-based communication.
2.2.4.3. Parallel Interface Operation
When the device is powered up for parallel interface, the pins include eight data lines (D7–D0), a single address
(A0), a read strobe (RD), a write strobe (WR), an interrupt line (INT), and chip select (CS). Table 23 summarizes
the parallel-interface signals:
Refer to the device data sheet for timing characteristics. Address pin A0 allows the host processor to choose
between the two interface registers, HIR0 and HIR1. The timing diagrams below show typical parallel-interface
operation. Refer to the respective product data sheets for timing specifications.
26
Signal
D[7:0]
WR
INT
CS
RD
A0
Table 23. Parallel Interface Signals
Read strobe (active low)
Write strobe (active low)
Chip Select (active low)
Interrupt (active low)
Register address
Function
Data bus
Rev. 1.3
Bidirectional
Direction
Output
Input
Input
Input
Input
Related parts for SI2457-D-FT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TSSOP 24/C°/56 KBPS, V.90 ISOMODEM SYSTEM-SIDE
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
TSSOP 24/I°/56 KBPS, V.90 ISOMODEM SYSTEM-SIDE
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
SMD/C°/SINGLE-ENDED OUTPUT SILICON OSCILLATOR
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
N/A N/A/SI4010 AES KEYFOB DEMO WITH LCD RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
N/A N/A/SI4010 SIMPLIFIED KEY FOB DEMO WITH LED RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
N/A/-40 TO 85 OC/EZLINK MODULE; F930/4432 HIGH BAND (REV E/B1)
Manufacturer:
Silicon Laboratories Inc