PQ30RV11 Sharp Electronics, PQ30RV11 Datasheet
PQ30RV11
Specifications of PQ30RV11
Available stocks
Related parts for PQ30RV11
PQ30RV11 Summary of contents
Page 1
... In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/ PQ30RV1/PQ30RV11/PQ30RV2/PQ30RV21 Variable Output Low Power-Loss Voltage Regulators Outline Dimensions 10 ...
Page 2
... Operating temperature Storage temperature Soldering temperature 1 All are open except GND and applicable terminals. 2 Overheat protection may operate at T >=125˚C. j Electrical Characteristics Unless otherwise specified, condition shall be V =15V, V =10V, I =0.5A, R =390 (PQ30RV1/PQ30RV11 =15V, V =10V, I =1.0A, R =390 (PQ30RV2/PQ30RV21 Parameter Input voltage ...
Page 3
... Low Power-Loss Voltage Regulators Fig. 3 Power Dissipation vs. Ambient Temperature (PQ30RV1/PQ30RV11 :No heat sink D1 P :With infinite heat sink – 100 Ambient temperature T Note) Oblique line portion : Overheat protection may operate in this area. Fig. 5 Overcurrent Protection Characteristics (PQ30RV1/PQ30RV11) 100 0.5 1.0 Output current I ...
Page 4
... Temperature (PQ30RV2/PQ30RV21) R =390 ,R =2. :input voltage shall be the IN value when output voltage is 95% in comparison with the initial value I =2A O 1. 100 Junction temperature T (˚C) j Frequency (PQ30RV1/PQ30RV11) C =3.3 F ref No C ref T =25˚ =390 ,R =2. =0.5A,e =0.5V, i(rms =15V IN 0 Input ripple frequency f (kHz) ...
Page 5
... Fig.16 Ripple Rejection vs. Output Current (PQ30RV1/PQ30RV11 100 Fig.18 Output Peak Current vs. Dropout Voltage (PQ30RV1/PQ30RV11) 2.0 1 1.0 0 0.8 1.0 Fig.20 Output Peak Current vs. Junction Temperature (PQ30RV1/PQ30RV11) 2.0 1.5 1 95% in comparison with the initial value R 0.5 – =3.3 F ref No C ref =25˚C j =390 ,R =2. =15V,e =0 ...
Page 6
... O The standard specification of C checking These devices are necessary to set the output voltage. The output voltage (1 ref 1.25V TYP) ref The standard value 390 . But value up 10k does not cause any trouble. 1 PQ30RV1/PQ30RV11/PQ30RV2/PQ30RV21 =5V 75 100 125 (˚ ref 4 + 390 10k may raise the gain, facilitating oscillation.) ...
Page 7
... Next, assuming that V (min)=0.5V for =(5V–0.5V)(R +R )/R R =0.49mA which is less than the rating Figure 1 shows the V –V characteristics when PQ30RV1/PQ30RV11/PQ30RV2/PQ30RV21 High : Output OFF V C Low : Output ON and (1.25V TYP)by applying the external signal, the output is turned off(pass transistor of must be higher then V ...
Page 8
... Control voltage V Model Line-ups for Lead Forming Type Output current 1A output Output voltage PQ30RV1B precision: 2.5% Outline Dimensions(PQ30RV1B/PQ30RV2B) 10.2MAX PQ30RV1 Internal connection diagram Note) The value of absolute maximum ratings and electrical characteristics is same as ones of PQ30RV1/2 series. PQ30RV1/PQ30RV11/PQ30RV2/PQ30RV21 V =17V =10k 1 R =115k ...
Page 9
NOTICE The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related ...