AT49BV8192-12TI Atmel, AT49BV8192-12TI Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
AT49BV8192-12TI
Manufacturer Part Number
AT49BV8192-12TI
Description
Manufacturer
Atmel
Datasheet
1.AT49BV8192-12TI.pdf
(15 pages)
Specifications of AT49BV8192-12TI
Cell Type
NOR
Density
8Mb
Access Time (max)
120ns
Interface Type
Parallel
Boot Type
Bottom
Address Bus
19b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 85C
Package Type
TSOP-I
Program/erase Volt (typ)
5V
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
16b
Number Of Words
512K
Supply Current
25mA
Mounting
Surface Mount
Pin Count
48
Lead Free Status / Rohs Status
Not Compliant
The device contains a user-enabled “boot block” protection
feature. Two versions of the feature are available: the
AT49BV/LV8192 locates the boot block at lowest order
addresses (“bottom boot”); the AT49BV/LV8192T locates it
at highest order addresses (“top boot”)
To allow for simple in-system reprogrammability, the
AT49BV/LV8192(T) does not require high input voltages for
programming. Reading data out of the device is similar to
reading from an EPROM; it has standard CE, OE, and WE
inputs to avoid bus contention. Reprogramming the
AT49BV/LV8192(T) is performed by first erasing a block of
data and then programming on a word-by-word basis.
The device is erased by executing the erase command
sequence; the device internally controls the erase opera-
tion. The memory is divided into three blocks for erase
operations. There are two 8K word parameter block sec-
tions and one sector consisting of the boot block and the
Block Diagram
Device Operation
READ: The AT49BV/LV8192(T) is accessed like an
EPROM. When CE and OE are low and WE is high, the
data stored at the memory location determined by the
address pins is asserted on the outputs. The outputs are
put in the high impedance state whenever CE or OE is
high. This dual-line control gives designers flexibility in pre-
venting bus contention.
COMMAND SEQUENCES: When the device is first pow-
ered on it will be reset to the read or standby mode
depending upon the state of the control line inputs. In order
to perform other device functions, a series of command
sequences are entered into the device. The command
sequences are shown in the Command Definitions table
(I/O8 - I/O15 are don't care inputs for the command codes).
The command sequences are written by applying a low
2
AT49BV/LV8192(T)
ADDRESS
INPUTS
RESET
VCC
VPP
GND
WE
OE
CE
Y DECODER
X DECODER
CONTROL
LOGIC
DATA INPUTS/OUTPUTS
PROGRAM DATA
INPUT/OUTPUT
MAIN MEMORY
(488K WORDS)
PARAMETER
PARAMETER
BOOT BLOCK
I/O0 - I/O15
8K WORDS
8K WORDS
AT49BV/LV8192
BUFFERS
LATCHES
Y-GATING
8K WORDS
BLOCK 2
BLOCK 1
main memory array block. The AT49BV/LV8192(T) is pro-
grammed on a word-by-word basis.
The device has the capability to protect the data in the boot
block; this feature is enabled by a command sequence.
Once the boot block programming lockout feature is
enabled, the data in the boot block cannot be changed
when input levels of 3.6 volts or less are used. The typical
number of program and erase cycles is in excess of 10,000
cycles.
The optional 8K word boot block section includes a repro-
gramming lock out feature to provide data integrity. The
boot sector is designed to contain user secure code, and
when the feature is enabled, the boot sector is protected
from being reprogrammed.
During a chip erase, sector erase, or word programming,
the V
pulse on the WE or CE input with CE or WE low (respec-
tively) and OE high. The address is latched on the falling
edge of CE or WE, whichever occurs last. The data is
latched by the first rising edge of CE or WE. Standard
microprocessor write timings are used. The address loca-
tions used in the command sequences are not affected by
entering the command sequences.
RESET: A RESET input pin is provided to ease some sys-
tem applications. When RESET is at a logic high level, the
device is in its standard operating mode. A low level on the
RESET input halts the present device operation and puts
the outputs of the device in a high impedance state. When
a high level is reasserted on the RESET pin, the device
returns to the Read or Standby mode, depending upon the
state of the control inputs. By applying a 12V
PP
7FFFF
05FFF
03FFF
01FFF
00000
06000
04000
02000
pin must be at 5V
DATA INPUTS/OUTPUTS
PROGRAM DATA
INPUT/OUTPUT
MAIN MEMORY
(488K WORDS)
BOOT BLOCK
PARAMETER
PARAMETER
I/O0 - I/O15
8K WORDS
8K WORDS
8K WORDS
BUFFERS
LATCHES
Y-GATING
AT49BV/LV8192T
BLOCK 1
BLOCK 2
10%.
7FFFF
7DFFF
7BFFF
7E000
7C000
7A000
79FFF
00000
0.5V input