AT49F080-90TI Atmel, AT49F080-90TI Datasheet - Page 3

• Manufacturer Part Number: AT49F080-90TI
• Manufacturer: Atmel

Specifications of AT49F080-90TI

• Cell Type: NOR
• Density: 8Mb
• Access Time (max): 90ns
• Interface Type: Parallel
• Boot Type: Bottom
• Address Bus: 20b
• Operating Supply Voltage (typ): 5V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP-I
• Program/erase Volt (typ): 5V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Word Size: 8b
• Number Of Words: 1M
• Supply Current: 50mA
• Mounting: Surface Mount
• Pin Count: 40
• Lead Free Status / Rohs Status: Not Compliant

optional to the user. The address range of the AT49F080
boot block is 00000H to 03FFFH while the address range
of the AT49F080T boot block is FC000H to FFFFFH.
To activate the lockout feature, a series of six program
commands to specific addresses with specific data must be
performed. Please refer to the Command Definitions table.
BOOT BLOCK LOCKOUT DETECTION: A software
method is available to determine if programming of the boot
block section is locked out. When the device is in the soft-
ware product identification mode (see Software Product
Identification Entry and Exit sections) a read from address
location 00002H will show if programming the boot block is
locked out for the AT49F080, and a read from address
location F3002H will show if programming the boot block is
locked out for the AT49F080T. If the data on I/O0 is low,
the boot block can be programmed; if the data on I/O0 is
high, the program lockout feature has been activated and
the block cannot be programmed. The software product
identification exit code should be used to return to standard
operation.
BOOT BLOCK PROGRAMMING LOCKOUT OVER-
RIDE: The user can override the boot block programming
lockout by taking the RESET pin to 12V
this, protected boot block data can be altered through a
chip erase, or byte programming. When the RESET pin is
brought back to TTL levels, the boot block programming
lockout feature is again active.
PRODUCT IDENTIFICATION: The product identification
mode identifies the device and manufacturer as Atmel. It
may be accessed by hardware or software operation. The
hardware operation mode can be used by an external pro-
grammer to identify the correct programming algorithm for
the Atmel product.
For details, see Operating Modes (for hardware operation)
or Software Product Identification. The manufacturer and
device code is the same for both modes.
DATA POLLING: The AT49F080(T) features DATA poll-
ing to indicate the end of a program cycle. During a pro-
gram cycle an attempted read of the last byte loaded will
result in the complement of the loaded data on I/O7. Once
the program cycle has been completed, true data is valid
0.5V. By doing
on all outputs and the next cycle may begin. DATA polling
may begin at any time during the program cycle.
T O G G L E B I T : I n a d d i t i o n t o D A T A p o l l i n g , t h e
AT49F080(T) provides another method for determining the
end of a program or erase cycle. During a program or erase
operation, successive attempts to read data from the
device will result in I/O6 toggling between one and zero.
Once the program cycle has completed, I/O6 will stop tog-
gling and valid data will be read. Examining the toggle bit
may begin at any time during a program cycle.
RDY/BUSY: An open drain READY/BUSY output pin pro-
vides another method of detecting the end of a program or
erase operation. RDY/BUSY is actively pulled low during
the internal program and erase cycles and is released at
the completion of the cycle. The open drain connection
allows for OR - tying of several devices to the same
RDY/BUSY line.
RESET: A RESET input pin is provided to ease some sys-
tem applications. When RESET is at a logic high level, the
device is in its standard operating mode. A low level on the
RESET input halts the present device operation and puts
the outputs of the device in a high impedance state. If the
RESET pin makes a high to low transition during a program
or erase operation, the operation may not be successfully
completed and the operation will have to be repeated after
a high level is applied to the RESET pin. When a high level
is reasserted on the RESET pin, the device returns to the
read or standby mode, depending upon the state of the
control inputs. By applying a 12V
RESET pin, the boot block array can be reprogrammed
even if the boot block lockout feature has been enabled
(see Boot Block Programming Lockout Override section).
HARDWARE DATA PROTECTION: Hardware features
protect against inadvertent programs to the AT49F080(T)
in the following ways: (a) V
(typical), the program function is inhibited. (b) Program
inhibit: holding any one of OE low, CE high or WE high
inhibits program cycles. (c) Noise filter: pulses of less than
15 ns (typical) on the WE or CE inputs will not initiate a pro-
gram cycle.
CC
sense: if V
0.5V input signal to the
CC
is below 3.8V
3