5962-9098902MLA E2V, 5962-9098902MLA Datasheet - Page 4

• Manufacturer Part Number: 5962-9098902MLA
• Manufacturer: E2V

Specifications of 5962-9098902MLA

• Lead Free Status / Rohs Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
22201; http://www.jedec.org.)
the documents. These documents also may be available in or through libraries or other informational services.)
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
shall be as specified on figure 2. When required in screening (see 4.2 herein) or qualification conformance inspection, groups A,
C, D, or E (see 4.4), the devices shall be programmed by the manufacturer prior to test. A minimum of 50 percent of the total
number of cells shall be programmed or at least 25 percent of the total number of cells to any altered item drawing.
drawing.
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
tests for each subgroup are defined in table I.
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
(Applications for copies should be addressed to the Electronics Industries Alliance, 2500 Wilson Boulevard, Arlington, VA
2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices for contracts involving no altered item drawing
3.2.3.2 Programmed devices. The truth table for programmed devices shall be as specified by an attached altered item
3.2.4 Radiation exposure circuit. The radiation exposure circuit will be provided when RHA product becomes available.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
(Non-Government standards and other publications are normally available from the organizations that prepare or distribute
ELECTRONICS INDUSTRIES ALLIANCE (EIA)
JEDEC Standard EIA/JESD 78 - IC Latch-Up Test.
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
STANDARD
SIZE
A
REVISION LEVEL
A
SHEET
5962-90989
4